Emerson LC320EM8A owner manual Initial Setting, Initial Setup

Page 12

INITIAL SETTING

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

5Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and auto channel scan, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure if the unit is connected to antenna or cable.

1 After making all the necessary connections, press [POWER] to turn on the unit.

• This operation may take a few moments.

2 Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI i i l Setup

 

 

 

 

 

 

 

Select the language for setup display.

 

English

 

 

Elija el idioma de ajuste.

 

 

Español

 

 

 

 

Français

 

Sélectionner langue écran config.

 

 

 

 

 

 

 

 

Select

ENTER Enter

SETUP

 

 

Exit

 

 

 

 

 

 

 

•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER].

3 Use [Cursor K/L] to select “Air” for TV channels or “Cable” for CATV channels, then press [ENTER].

InitialI i i l Setup

Make sure the antenna is connected to "ANT.IN" jack.

Air

Select the destination of "ANT.IN" jack.

 

Cable

 

 

 

Air

 

 

 

Cable

Or

 

 

 

ANT.IN

 

 

 

 

Select

ENTER Enter

BACK

SETUP

Back

Exit

•Scanning and memorizing of channels start automatically.

InitialI i i l Setup

Now the system is scanning for channels,please wait.

5%

Analog channels

1ch

 

 

 

 

 

 

 

 

Digital channels

0ch

 

 

 

 

 

 

 

SETUP

Exit

•When the scanning and memorizing are completed, the lowest memorized channel in the broadcasting will be displayed.

Note:

•If you connect the cable system directly, contact the CATV installer.

•If you press [POWER] or [SETUP] during auto channel scan, this setting will be canceled.

•The initial auto channel scan function can be executed for either “Air” or “Cable” only once. When you change the connection (Air/Cable), set auto channel scan again. (Refer to page 13.)

•You can cancel or exit the initial auto channel scan menu by pressing [SETUP].

•If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the unit, “Helpful Hints” appears. Follow the instructions listed on the TV screen.

2-2

No channel is registered.

Press and hold "ENTER" key on the remote control for 3 seconds.

Contact support hotline provided on manual or back of unit.

Sin canal registrado.

Pulse durante 3 segundos la tecla "ENTER" en el control remoto.

Llame teléfono de apoyo en manual o atrás de TV.

Pas de chaîne consign.

Enfoncez "ENTER" 3 secondes sur la télécommande.

Contacter numero d'urgence dans manuel ou arrière appareil.

12

EN

Page 11 Page 13
Image 12
Page 11 Page 13
Contents LC320EM8A Introduction Important note is located on the rear of the cabinetPrecautions RADIO-TV InterferenceSupplied Accessories Symbols Used in this ManualRemote control LocationFeatures ContentsDTV/TV/CATV Remote Control Function Installing the BatteriesControl Panel Rear PanelConnection Basic ConnectionAntenna Cable Connection Connection to Cable Box or Satellite BoxExternal Device Connection Hdmi ConnectionHDMI-DVI Connection Component Video Cable Connection Video Cable ConnectionVideo Connection Audio Output Connection DigitalAnalog Initial Setting Initial SetupMake sure if the unit is connected to antenna or cable Scanning and memorizing of channels start automaticallyMain Menu Auto Channel ScanPress Setup to exit Language SelectionLanguage 5Volume Adjustment Watching TVChannel Selection Still Mode Switching Each ModeYou can freeze the image shown on the TV screen To use the Hdmi in jack on the unit, select HdmiSwitching Audio Mode StereoSAP MonoScreen Information Press InfoBroadcasting Information Day of MemoriesiTV Screen Display Mode Sleep Timer Press Sleep to set the sleep timerTo Cancel the Sleep Timer Optional Setting Channel List5Manual Register Antenna Confirmation AntennaPicture Adjustment Closed Caption DTV Closed Caption DTV CCUse Cursor K/L to select DTV CC, then press CC Style Font StyleFont Size Font Color Font OpacityBack Color Back OpacitySee the following description for setting each item Chipip Enter passwordChip Use Cursor K/L to select V-chip, then pressPress Setup to exit Use Cursor K/L to select Mpaa Rating, then press EnterView and Block To Set the Sub RatingsUse Cursor K/L to select New Password, then press Enter Chipip Enter password Confirm passwordHdmi Audio You can set the method of sound input for the Hdmi in jackUse Cursor K/L to select Hdmi Audio, then press Troubleshooting Troubleshooting GuideCheck the batteries of the remote control Refer to IR Signal Check onInterrupt the remote control signal of this unit Delayed behind the dialogueMaintenance InformationGlossary AtscGeneral Specifications Electrical SpecificationOther Specifications Cable Channel DesignationsLimited Warranty
Top Page Image Contents