Emerson LC320EM8A owner manual Optional Setting, Channel List, 5Manual Register

Page 21

OPTIONAL SETTING

5Channel List

The channel list function lets you remove undesired channels from the channel registration list.

1 Press [SETUP] to display the main menu.

2 Use [Cursor K/L] to select “CHANNEL”, then press

[ENTER].

3 Use [Cursor K/L] to select “Channel List”, then press [ENTER].

Channell

Autoscan

Channel List

Manual Register

Antenna

4 Use [Cursor K/L] to select the channel you want to remove, then press [ENTER].

Channell Listi

Highlight channels for

DTV

6

Ch Up/Down key selection.

 

 

 

 

27

 

 

 

 

DTV

8

 

 

 

 

 

9

 

 

 

 

DTV

48

58

DTV 67

BACK

Ch Select ENTER Watch/Skip Back

•The channel display for the removed channel darkens. You will not be able to select the channel again using [CH K/L].

•To reactivate a removed channel, highlight it using [Cursor K/L] and press [ENTER]. The channel display lightens.

•When you remove a major channel, its minor channels are removed as well.

Note:

•The channel with the “DTV” indicated on the display is ATSC. Otherwise the channel is NTSC.

5 Press [SETUP] to exit.

5Manual Register

 

 

 

INTRODUCTION

 

 

 

 

The manual register function lets you add the channels that were not added

 

by the auto channel scan due to the reception condition at the initial setting.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Press [SETUP] to display the main menu.

 

 

 

CONNECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 Use [Cursor K/L] to select “CHANNEL”, then press

 

 

[ENTER].

 

 

 

INITIAL SETTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WATCHING

 

 

 

 

 

 

 

3 Use [Cursor K/L] to select “Manual Register”, then

press [ENTER].

 

 

 

TV

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Channell

 

 

 

 

 

 

Autoscan

 

 

 

 

 

 

Channel List

 

 

 

OPTIONALSETTING

 

 

Manual Register

 

 

 

 

 

Antenna

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 Use [the Number buttons] to enter the number of the

 

 

channel you want to add, then press [ENTER].

 

 

 

TROUBLESHOOTING

 

 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Manuall Registeri

 

 

 

 

 

 

For analog channels,

Register

 

 

 

 

 

select a channel to register using

 

 

 

 

 

 

number keys.

 

 

 

 

 

 

 

 

 

 

For digital channels,

 

 

 

 

 

 

you must perform Autoscan function.

 

 

 

INFORMATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK

Back

 

 

 

 

Ch Change

 

 

 

 

 

 

 

 

 

 

5 Press [SETUP] to exit.

 

 

 

 

 

 

 

 

Note:

•If set up completes successfully, “Registered to the Channel List” is displayed.

•If external input is used, it is not possible to register the channel and “Unavailable” will be displayed on the TV screen.

21

EN

Page 20 Page 22
Image 21
Page 20 Page 22
Contents LC320EM8A Important note is located on the rear of the cabinet IntroductionRADIO-TV Interference PrecautionsSymbols Used in this Manual Supplied AccessoriesRemote control LocationFeatures ContentsDTV/TV/CATV Installing the Batteries Remote Control FunctionRear Panel Control PanelBasic Connection ConnectionAntenna Cable Connection Connection to Cable Box or Satellite BoxExternal Device Connection Hdmi ConnectionHDMI-DVI Connection Video Cable Connection Component Video Cable ConnectionVideo Connection Audio Output Connection DigitalAnalog Initial Setup Initial SettingMake sure if the unit is connected to antenna or cable Scanning and memorizing of channels start automaticallyAuto Channel Scan Main MenuPress Setup to exit Language SelectionLanguage 5Volume Adjustment Watching TVChannel Selection Switching Each Mode Still ModeYou can freeze the image shown on the TV screen To use the Hdmi in jack on the unit, select HdmiStereo Switching Audio ModeSAP MonoPress Info Screen InformationBroadcasting Information Day of MemoriesiTV Screen Display Mode Sleep Timer Press Sleep to set the sleep timerTo Cancel the Sleep Timer Optional Setting Channel List5Manual Register Antenna Antenna ConfirmationPicture Adjustment Closed Caption DTV Closed Caption DTV CCUse Cursor K/L to select DTV CC, then press CC Style Font StyleFont Size Font Opacity Font ColorBack Color Back OpacityChipip Enter password See the following description for setting each itemChip Use Cursor K/L to select V-chip, then pressUse Cursor K/L to select Mpaa Rating, then press Enter Press Setup to exitView and Block To Set the Sub RatingsChipip Enter password Confirm password Use Cursor K/L to select New Password, then press EnterHdmi Audio You can set the method of sound input for the Hdmi in jackUse Cursor K/L to select Hdmi Audio, then press Troubleshooting Guide TroubleshootingRefer to IR Signal Check on Check the batteries of the remote controlInterrupt the remote control signal of this unit Delayed behind the dialogueInformation MaintenanceGlossary AtscElectrical Specification General SpecificationsOther Specifications Cable Channel DesignationsLimited Warranty
Top Page Image Contents