Option Menu
Using the OPTION menu, the five items shown in the Table below can be performed.
Please perform each operation according to the instructions in the Table.
Example: OPTION Menu
|
|
|
|
|
|
|
| (VOLUME) | |||
|
|
|
|
|
|
|
|
|
|
|
|
Item |
|
|
|
|
|
|
| Description |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
VOLUME | Adjust Volume: High |
|
|
| Low |
| |||||
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
| |
AUTO OFF | Adjust AUTO OFF Time: |
|
|
|
|
|
|
| |||
| Long (MAX. 99 min.) |
|
|
| Short (Min. 1 min.) |
|
| (DISABLE: 0 | |||
|
|
|
|
| |||||||
| min.) The system automatically |
| the standby mode if no signal |
|
| ||||||
| enters | is received within | |||||||||
| the set time. This function is inactive when DISABLE (0 min.) is selected. |
| |||||||||
|
|
|
|
|
|
|
|
|
|
| |
WHISPER | Select WHISPER Mode: |
|
|
|
|
|
|
| |||
| NORMAL |
|
|
| WHISPER |
| |||||
|
|
|
| ||||||||
| When WHISPER is selected the WHISPER mode is activated. In the WHISPER mode, | ||||||||||
| acoustic noise and screen brightness are reduced. |
| |||||||||
|
|
|
|
|
|
|
|
| |||
LAMP TIME | Refer to LAMP TIME: When set, this function displays the total time the projector lamp | ||||||||||
| has been used since new. |
|
|
|
|
|
|
| |||
| Reset LAMP TIME [Use this function only when the lamp has been replaced!]: | ||||||||||
| Depress the RESET button for at least 3 seconds while lamp time is being displayed. The | ||||||||||
| reset menu will then appear. After you replace the lamp with a new lamp, select RESET | ||||||||||
| on the menu with the |
| button. |
| |||||||
| • Do not reset the lamp time unless you have replaced the lamp. And, always | ||||||||||
|
| reset the lamp time when replacing the lamp. |
| ||||||||
| • Before replacing the lamp, carefully read the lamp maintenance section. | ||||||||||
|
|
|
|
|
|
|
|
|
| ||
FILTER TIME | Refer to FILTER TIME: This function displays the total time the |
| |||||||||
| been used since it was installed. |
| |||||||||
| Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]: | ||||||||||
| Depress the RESET button for at least 3 seconds while lamp time is being displayed. The | ||||||||||
| reset menu will then appear. After you replace the filter, select RESET on the menu with | ||||||||||
| the | button. |
|
|
|
|
|
|
| ||
| DEFAULT |
|
| CANCEL |
| ||||||
|
|
|
| ||||||||
| • Do not reset the filter time unless you have cleaned or replaced the filter. And, | ||||||||||
|
| always reset the filter time when cleaning or replacing the filter. The message | |||||||||
|
| functions will not operate properly if the filter time is not reset correctly. | |||||||||
| • Before cleaning or replacing the filter, carefully read the descriptions titled | ||||||||||
|
| "THE AIR FILTER”. |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
28 ViewSonic PJ751