Runco PL-61DHD Installation, Considerations, Mounting the PlasmaWall, On a Wall or Table Stand

Page 28

Installation

3.3

Proper installation of your PlasmaWall will ensure the highest possible picture quality.

Installation

Whether you are installing the PlasmaWall temporarily or permanently, you should take the

Considerations

following into account to ensure that it performs optimally.

 

 

Mounting the PlasmaWall ➤

To install the PlasmaWall, you will need either an optional table stand or wall-mounting kit.

on a Wall or Table Stand

The PlasmaWall cannot be installed on its own.

 

If you do decide to wall-mount the PlasmaWall, ensure that the wall-mount bracket is

 

installed according to the instructions included with it. The wall must be capable of

 

supporting a redundant weight factor three (3) times the weight of the display, or be

 

reinforced.

 

 

Runco recommends that this be done by a custom installation specialist.

 

Note

Use only a Runco-approved wall-mount kit or table stand that is

 

specifically designed for your display.

You can attach your optional mounts or stand to the PlasmaWall in either of two ways:

• While it is upright.

•As it lies flat with the screen face down. Place the protective sheet, which was wrapped around the plasma monitor when it was packaged, between the screen and your work surface to avoid scratching or otherwise damaging the screen surface.

Ambient Light ➤ In general, minimize or eliminate light sources directed at the display. Contrast ratio in your images will be noticeably reduced if light directly strikes the display, such as when a shaft of light from a window or floodlight falls on the image. Images may then appear washed out and less vibrant.

18

Runco PlasmaWall Owner’s Operating Manual

Page 27 Page 29
Image 28
Page 27 Page 29
Contents PL-61DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsPlasmaWall at a Glance Input SELECT/EXIT Power on/off switch does not disconnect the plasma displayMENU/ENTER AUDIO1, AUDIO2, AUDIO3 External Speaker OutputsCOMPONENT1 DHD Controller Front Panel Runco IconIR Sensor Vacuum Fluorescent DisplayUP Button Left ButtonEnter Button Down ButtonHD1 / HD2 Analog BNC connectors Component Video RCA connectorsDHD Controller Rear Panel DVI OUTMain Power Switch Composite Video InputRS-232 Control Port Main AC FuseDHD Controller Remote Control DHD Controller Remote ControlIR Output Indicator EnterLight MenuCinema SVCISF DAY CustInstallation Remote ControlOther surfaces Installation specialist Quick SetupStep Procedure For Details, refer to Installation ConsiderationsMounting the PlasmaWall On a Wall or Table StandOther Considerations VentilationProlong operating life Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerDHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source DTV or Progressive Component YPbPr Source Refer to Computer/Video Signal Compatibility on page 58 for Analog Computer RGB Connections See FigureTo work Some Macintosh computers may require a Macintosh videoComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection11. Installing the Cable Clamps Cable ManagementInstallation Turning on the Power OperationSelecting the Input Source Setting the PC Display Properties You must enter a passcode to access the Service menuOperation Using the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.002B Date Mar 24You must enter a passcode to access the Calibration menu Gain/Offset Refer to ISF Night Display Color, aboveISF Day Display Color Refer to ISF Night Display Color CalibrationService Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD Button takes you from top to bottom in the left column, thenDisabled HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation Operation Troubleshooting Tips Maintenance and TroubleshootingSymptom Possible Causes Solution Computer/Video Signal Value Description Min/max Stored? Power On/Off Commands CommandSerial Communications Aspect Ratio Commands Image Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Serial Communications Specifications PlasmaWall SpecificationsDHD Controller Specifications PlasmaWall Dimensions PlasmaWall Model PL-61DHD DimensionsComputer/Video Signal Compatibility Computer/Video Signal Compatibility ChartSUN Specifications Page Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 68 pages 9.69 Kb

PL-61DHD specifications

The Runco PL-61DHD is a premium plasma television that has captured the attention of home theater enthusiasts since its introduction. With a striking 61-inch display, this model combines advanced technology with elegant design to create a stunning viewing experience.

One of the standout features of the PL-61DHD is its impressive picture quality. The television boasts a full HD resolution of 1920 x 1080 pixels, which ensures that every image is sharp and vibrant. This high resolution, combined with Runco's proprietary video processing technology, delivers exceptional color accuracy and contrast, making it suitable for a range of content from movies to sports broadcasts.

The PL-61DHD employs Runco's unique Color Fidelity technology, which enhances the precision of colors on the screen. This technology ensures that viewers experience shades that are true to life, which significantly elevates the overall viewing experience. Moreover, the plasma panel excels in black levels and contrast ratios, providing deep blacks and bright highlights that make images pop.

Another impressive feature of the PL-61DHD is its ambient light rejection capability. This allows the television to perform remarkably well in various lighting conditions, making it versatile for different room environments. Whether in a dimly lit theater room or a bright living space, the PL-61DHD adapts to deliver optimal performance.

To facilitate seamless connectivity, the Runco PL-61DHD includes multiple input options, such as HDMI and component video. This range of connections allows users to hook up various devices, including Blu-ray players, gaming consoles, and streaming devices, maximizing the television's usability and making it a central hub for home entertainment.

The build quality of the PL-61DHD reflects Runco's commitment to excellence. The sleek and stylish design not only enhances the aesthetics of any room but is also engineered for durability. The unit’s robust construction ensures longevity, making it a solid investment for avid home theater enthusiasts.

In conclusion, the Runco PL-61DHD stands out in the world of high-end televisions due to its unparalleled picture quality, advanced technology features, and stylish design. It is a definitive choice for anyone looking to elevate their home viewing experience, making it a timeless addition to any home theater setup.
Top Page Image Contents