Runco PL-61DHD manual Serial Communications, Command

Page 59

6. Serial Communications

To interface the PlasmaWall with a home theater automation/control system or a PC running terminal emulation software, connect it to the RS-232 output of the DHD Controller as shown in Figure 3-4.Connect your control system or PC to the RS-232 input of the DHD Controller as shown in Figure 3-9.

Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 19200, to match that of the DHD Controller RS-232 port.

Serial commands to the DHD Controller take the following form:

•Commands are not case-sensitive.

•For a single command that takes no parameters, type the command followed by a carriage return; for example, to set the aspect ratio to Letterbox, type

LETTERBOX <Enter>.

•For a single command that takes a parameter, type the command, a space or a comma and the desired value followed by a carriage return; for example, to set the brightness to -10, type BRIGHTNESS -10<Enter> or

BRIGHTNESS,-10 <Enter>.

•You can also send a string of multiple commands on a single line, separated by commas. For example, COMPOSITE,BRIGHTNESS 100,ANAMORPHIC <Enter> switches to the Composite video input, sets the brightness to 100 and sets the aspect ratio to Anamorphic. Command strings can be up to 255 characters long.

Avoid combining the ON or POWER 1 commands with other commands Note on a single line. After sending ON or POWER 1, allow at least 15

seconds for the DHD Controller to power up. Once it does, it will accept and properly execute multiple serial commands.

Table 6-1lists the RS-232 command set. The “Parameter (min/max)” column shows the valid parameter ranges, or “NA” for commands that take no parameters.

When you enter a valid command, the DHD Controller executes it and acknowledges it with a plus sign on the command line (+ >). When you enter an invalid command – one that is misspelled or followed by values outside the valid range for that command – the DHD Controller ignores it and returns a minus sign (- >).

Table 6-1. Serial Commands

Command

Parameter

 

Value

Description

(min/max)

 

Stored?

 

 

 

 

 

 

 

 

 

 

Power On/Off Commands

 

 

 

 

 

OFF

NA

 

NA

Turns system off

 

 

 

 

 

ON

NA

 

NA

Turns system on

 

 

 

 

 

POWER

0/1

 

NA

Turns system on or off (toggles on/off state)

 

 

 

 

 

POWER?

NA

 

NA

Returns power status

 

 

 

 

 

6.1

RS-232 Connection and Port Configuration

6.2

Serial Command Syntax

Runco PlasmaWall Owner’s Operating Manual

49

Page 58 Page 60
Image 59
Page 58 Page 60
Contents PL-61DHD Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC DOC Compliance Notice Safety PrecautionsTable of Contents Serial Communications Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationKey Features and Benefits Description, Features and BenefitsOptional Accessories PlasmaWall at a Glance Controls and IndicatorsControls and Functions MENU/ENTER Power on/off switch does not disconnect the plasma displayInput SELECT/EXIT COMPONENT1 External Speaker OutputsAUDIO1, AUDIO2, AUDIO3 Vacuum Fluorescent Display DHD Controller Front PanelRunco Icon IR SensorDown Button UP ButtonLeft Button Enter ButtonDVI OUT HD1 / HD2 Analog BNC connectorsComponent Video RCA connectors DHD Controller Rear PanelMain AC Fuse Main Power SwitchComposite Video Input RS-232 Control PortDHD Controller Remote Control DHD Controller Remote ControlMenu IR Output IndicatorEnter LightCust CinemaSVC ISF DAYRemote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupInstallation specialist On a Wall or Table Stand InstallationConsiderations Mounting the PlasmaWallProlong operating life VentilationOther Considerations DHD Controller Connecting PlasmaWall to the DHD ControllerConnections to the PlasmaWall and DHD Controller RS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source DTV or Progressive Component YPbPr Source Some Macintosh computers may require a Macintosh video Refer to Computer/Video Signal Compatibility on page 58 forAnalog Computer RGB Connections See Figure To workComposite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureConnection RS-232 ControllerCable Management 11. Installing the Cable ClampsInstallation Operation Turning on the PowerYou must enter a passcode to access the Service menu Selecting the Input Source Setting the PC Display PropertiesOperation Using the On-Screen Menus Aspect Ratio ISF PresetsService Input SourceHD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect RatioRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan ResolutionInput Position Serial Number Hardware Firmware 0002.002B Date Mar 24 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above ISF Day Display Color Refer to ISF Night Display ColorShould be used by ISF-certified technicians only ServiceButton takes you from top to bottom in the left column, then Input Names Restore Composite Video Component SDHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV DisabledOperation Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Computer/Video Signal Serial Communications CommandValue Description Min/max Stored? Power On/Off Commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Serial Communications PlasmaWall Specifications SpecificationsDHD Controller Specifications PlasmaWall Model PL-61DHD Dimensions PlasmaWall DimensionsComputer/Video Signal Compatibility Chart Computer/Video Signal CompatibilitySUN Specifications Page Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 68 pages 9.69 Kb

PL-61DHD specifications

The Runco PL-61DHD is a premium plasma television that has captured the attention of home theater enthusiasts since its introduction. With a striking 61-inch display, this model combines advanced technology with elegant design to create a stunning viewing experience.

One of the standout features of the PL-61DHD is its impressive picture quality. The television boasts a full HD resolution of 1920 x 1080 pixels, which ensures that every image is sharp and vibrant. This high resolution, combined with Runco's proprietary video processing technology, delivers exceptional color accuracy and contrast, making it suitable for a range of content from movies to sports broadcasts.

The PL-61DHD employs Runco's unique Color Fidelity technology, which enhances the precision of colors on the screen. This technology ensures that viewers experience shades that are true to life, which significantly elevates the overall viewing experience. Moreover, the plasma panel excels in black levels and contrast ratios, providing deep blacks and bright highlights that make images pop.

Another impressive feature of the PL-61DHD is its ambient light rejection capability. This allows the television to perform remarkably well in various lighting conditions, making it versatile for different room environments. Whether in a dimly lit theater room or a bright living space, the PL-61DHD adapts to deliver optimal performance.

To facilitate seamless connectivity, the Runco PL-61DHD includes multiple input options, such as HDMI and component video. This range of connections allows users to hook up various devices, including Blu-ray players, gaming consoles, and streaming devices, maximizing the television's usability and making it a central hub for home entertainment.

The build quality of the PL-61DHD reflects Runco's commitment to excellence. The sleek and stylish design not only enhances the aesthetics of any room but is also engineered for durability. The unit’s robust construction ensures longevity, making it a solid investment for avid home theater enthusiasts.

In conclusion, the Runco PL-61DHD stands out in the world of high-end televisions due to its unparalleled picture quality, advanced technology features, and stylish design. It is a definitive choice for anyone looking to elevate their home viewing experience, making it a timeless addition to any home theater setup.
Top Page Image Contents