Sanyo PDP-42XR9DA Preparations, Using the Remote Control, Installing the Batteries

Page 7

Preparations

Using the Remote Control

<Use the remote control by pointing it towards the remote sensor window of the set. Objects between the remote control and sensor window may prevent proper operation.

30

30

5m

Cautions regarding use of remote control

<Do not expose the remote control to shock. In addition, do not expose the remote control to liquids, and do not place in an area with high humidity.

<Do not install or place the remote control under direct sunlight. The heat may cause deformation

of the unit.

<The remote control may not work properly if the remote sensor window of the main unit is under direct sunlight or strong lighting. In such a case, change the angle of the lighting or the TV set, or operate the remote control closer to the remote sensor window.

Installing the Batteries

If the remote control fails to operate the TV functions, replace the batteries in the remote control.

1 Open the battery cover.

2 Insert two size-AAA batteries.

<(Place the batteries with their terminals corresponding to the (+) and (–) indications in the battery compartment.)

3 Replace the cover and slide in reverse until the lock snaps.

Precaution on battery use

Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the instructions below.

<Place batteries with their terminals corresponding to the (+) and (–) indications. <Different types of batteries have different characteristics. Do not mix batteries of different types.

<Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/or cause old batteries to leak chemicals.

<Remove batteries as soon as they are non-operable. Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a cloth.

<If the remote control is not used for an extended period of time, remove the batteries from the remote control. <The batteries (battery pack of batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

4

Image 7
Contents PDP TV Important Information Table of Contents Important Safety Precautions Important Safety Precautions Important Notice To clean this unit, wipe with a soft, dry clothDo not use in hot and cold rooms locations Installing the Batteries Using the Remote ControlPreparations Antenna Connection Power ConnectionMain Unit front view/side view Indicator/Remote Sensor CH+Power Identification of ControlsMain Unit rear view Colored buttons RED/GREEN/YELLOW/BLUE Direct Remote Control UnitTo playback Camcorder Connecting a CamcorderConnections TV SideConnecting a Computer Connecting Component VideoTo play from the device using Hdmi Connecting an Hdmi deviceConnecting a VCR for Recording How to connect a device using Hdmi ConnectionTV Left Side Connecting Digital Coaxial AudioConnecting Headphones Coaxial audio cable Pdif in Coaxial Audio ProcessorTo navigate through the OSD main menu Basic OperationsMain Menu Overview List of main menus to help you with operationsTurning Off Turning On/Off the PowerFirst Time Setup Turning OnDisplaying the Information Banner Selecting the Input Signal SourcePress 3,4or OK to confirm the selection Auto Channel Search Memorizing the ChannelsManual Searching for DTV programs Setting Audio System Manual Fine TuningManual Searching for ATV programs Labeling Channels Setting Favorite ChannelsOpen the Programme Edit menu To delete channels Channel List ManagementTo skip unnecessary channels To sort channelsChannel and Program Selection Customizing the Picture Picture AdjustmentUsing the volume buttons VOL+ and VOL Sound AdjustmentAdjusting the Volume Adjusting the SoundIGR German stereo system Broadcasts Stereo/Bilingual Selection for analog channelsAudio Track Selection for digital channels Nicam Broadcast SelectionHearing Impaired System SetupSystem Setup System Update TimeTo create a new password Rating and Lock SetupPassword Setup Block Program SetupLock Tuning Setup Parental Guidance Setup DTV onlyRestoring Factory Default Time Zone Selection Timer SetupCurrent Time Setup On Timer SetupSleep Timer Setup Off Timer SetupAuto Sleep Setup Press Yellow button again to exit EPG OperationOpereation Program’s information will be displayedTeletext Teletext & SubtitleSubtitle Such as position and phase Screen Setup for D-SUBPC ModeScreen Setup Auto adjustHotel Mode Setup Hotel Mode SetupHotel Mode Remote control does not operate TroubleshootingDouble images Select them with 0-9 number buttons Current input modeOne or some channels can’t be Displayed SectionPDP TV Specifications5944035300 Ver