Palsonic DVD R 212 manual One Touch Recording OTR, DV Controlled Recording

Page 18

Recording Mode

Recording Process Control (continued)

2.Use the corresponding function keys of the remote controller, such as "RECORD", "PAUSE/STEP" and "STOP" to select from "Record, "Pause" and "Stop" functions in the recording process.

When a "Stop" operation is done, the system will write some information into the disc. The system will not respond to any button pressing at that time.

When you resume recording after the "Stop" operation, the system will add a title. If there is no interruption in the recording process from the beginning to the end, then only one title is available for the entire disc.

One Touch Recording (OTR)

This function enables you to set up the timer during the recording process. Once the scheduled time is reached, the system will stop recording automatically.

1.Enter the "Recording Mode" and start recording.

2.For desired timer recording, press the "REC/OTR" button once or several times.

The recording time will increase by 30 minutes with every pressing of the "REC/OTR" button. If the scheduled time exceeds the recordable time of the disc, normal recording mode will restore.

If the timer recording is paused or stopped, the system will cancel the timer recording process.

DV Controlled Recording

1. This unit can realise real-time monitoring and recording for a DV through the IEEE 1394 serial port (DV).

Connect the DV to the unit (for details, see "System Connection: System Connection for Recording External Signals") by the front panel inputs.

Switch on the power of the unit.

Press the "DV" button.

Switch on the "Power" button of the DV, set it to the "CAMERA" mode, and start monitoring.

Press the "REC/OTR" button to start recording. (Other operations is the same as in the Recording Mode).

2. This unit can also record the VCR content of the DV.

The connection method is the same as stated in the first 3 steps of 1.

Switch on the "Power" button of the DV to enter the VCR status, and the VCR status is "Stop".

Use the remote controller of the unit to complete the operations of the DV, including STOP, PLAY, PAUSE, FB, FF, etc.

Press the "REC/OTR" button and then press the "PLAY" button to start recording.

During the recording process, press the "PAUSE" button to suspend recording of the unit, and press the button again to suspend the DV. To restore play of the DV, press the "PLAY" button; if you press the "REC/OTR" button, the play of the DV and the recording of the unit will resume at the same time; press the "FWD", "REV" button to complete forward or rewind operation for the DV, while it reports Pause status to the unit; If you press the "STOP" button, the recording of the unit will stop first, and press again to stop the play of the DV.

Caution:

Do not move the unit or switch off the power during the recording process.

The finalised DVD+R disc shall not be recorded.

Be sure to switch off the power of the unit and the DV before connecting the DV cables.

17

Page 17 Page 19
Image 18
Page 17 Page 19
Contents DVD Recorder Safety Instructions Maintenance NoticeTable of Contents Disc Operations Introduction Enter the Title Editing modePlay Mode Title EditChannel Scan Basic Information DVD+R Disc Terms DVD DiscDVD+RW Disc Erasing the DiscMultiple Angles function Terms ChapterTrack Multiple Languages functionFront Panel Rear PanelRemote Control How to install and use the remote controller System Connection Connected to a TVConnect to an ordinary stereo system Rear Panel of the UnitConnect to an amplifier with digital decoder Recorder Front Selection of Monitor Signals Monitoring ModeNavigation Mode Use the menu to select monitoring signalsGeneral steps for recording external signals are as follows Recording ModeEnter the recording mode and menu description General StepsManual Recording Start Recording Recording Process ControlButton to select the Quality menu. Press One Touch Recording OTR DV Controlled RecordingTimer recording, set the system clock first. For Timer RecordingPrograms, the unit can satisfy your need. Before setting up Instructions, see System Setup System Clock SettingBox will appear on the right. Highlight the box and press Timer Recording Menu Description Entering the Chapter Editing ModeChapter Editing Operation Steps Select the title to be editedHide/Unhide Chapter Split TitleChapter Marker Index PictureOperation Steps Erase Disc Enter the Disc Operation ModeDisc Operation Lock DiscOverwrite Disc Rename DiscRecord a New Title Finalize DiscEnter the Title Editing Mode Title EditingOperation Play ModeEnter the Play Mode Direct PlayEnter Menu before Playing End PlayPlay Mode Control Normal PlayRandom Play Play Mode Control Program Play MP3Status-play item and press the Select button Play Process ControlMenu Operation Forward PlayPlay Process Control Pause/Step Play Volume ControlSelection Play Mode Chapter SelectionSelection Play Mode Track Selection Track Selection Play for Audio DiscTime Selection Play Mode Use of the Goto Button Audio SelectionAudio Channel Selection PBC ON/OFF Available only for VCD 2.0 or above versions Multi-angle SwitchSubtitle Selection Picture Zoom FunctionGeneral Settings Playback Settings System SetupOperational Interface and General Setup Language SettingsProgressive/Interlace Screen Saver SettingsRestore Factory Settings Video OutTV Aspect Ratio Settings Rating LevelDigital Audio Output Settings Analog Audio OutputRecording Quality Selection Recording SettingsAuto Chapter Marker Use Button to select a desired value and pressMenu Language Settings Subtitle Language SettingsAudio Language Settings Channel ScanMeanings of the icons System Clock Setting Other Operations StandbyAppendix Troubleshooting Guide Supported disc formats Technical SpecificationsTechnical Specifications Supported recordable discTechnical Specifications Palsonic Customer Service Telephone
Top Page Image Contents