Palsonic 86WSHDA, 76WSHDA owner manual To connect XGA input interface, To connect Hdtv set top box

Page 12

4. To connect XGA input interface

The figure below shows how to connect the set to the computer through XGA interface.

	THE SET'S REAR					COMPUTER
	RF	AV1	AV2	AV
	RF	IN	IN	OUT
	DVD IN			S-VIDEO
	DVD IN
	Y				VIDEO
	CB				L/MONO
	CR				R	:Direction of the signal
			HDTV IN		XGA	W :White (audio L/MONO)
	Y	PBPR	HDTV IN			R :Red (audio R)

R W

R

W

Signals

Press AV/TV button to display the signal source selection menu and select XGA mode. At this time the screen will display information from the computer.

5. To connect HDTV set top box

If your HDTV set top box is incorporated with YPbPr terminals, connect the set top box to the TV set through the YPbPr terminals, connect audio lines from set top box to HDTV IN L/R sound inputs, note that L to Land R to R.

(If your set top box is incorporated with XGA interface, please connect according to "To connect XGA input interface" which is shown above).

THE SET'S REAR

RF		AV1	AV2	AV
RF		IN	IN	OUT
DVD IN				S-VIDEO
DVD IN
Y					VIDEO
CB					L/MONO
CR					R
Y	PB	PR	HDTV IN		XGA
Y	PB	PR			XGA

:Direction of the signal

W:White (audio L/MONO)

	R :Red (audio R, PR)	HDTV set top box
	G :Green (Y)	HDTV set top box
	G :Green (Y)
	B :Blue (PB)
		G B R R W

G B

YPB

R

PR

R

R

Y PB PR R L/MONO

W

L/MONOSignals

Press AV/TV button to display the signal source selection menu and then select YPbPr mode. Now you can view programs play backed by the set top box.

10

Image 12

Contents 76CM/86CM Wide Screen Hdtv Ready Contents Page Page Location of controls Front view/Side view/Back viewFront view Side view Back view Remote Controller Remote controllerBattery installation Effective range of the RemoteInstallation Antenna connection/External equipment connectionsAntenna connection External Equipment Connections To connect AV input terminalsExternal equipment connections To connect DVD input terminalsTo connect XGA input interface To connect Hdtv set top boxTurning on/off & Signal source selection Signal source selectionBasic Operations Turning onBelow is a menu overview in RF TV mode Menu introductionMenu introduction Operations in RF mode Auto search/Manual searchAuto search Manual searchSetting of colour and sound system Setting of colour and sound systemWhen the colour of the picture is abnormal When the sound is abnormalChannel Presetting Fine tuningAFC Auto Frequency Control Fine tuneTo skip unnecessary channels/VCR To skip unnecessary channelsUsing the direct select buttons Using the Channel up/down buttonsUsing the Previous channel button Channel SelectionPicture adjustment Picture adjustmentMaking use of Personal button Making use of Picture menuPicture Rotate DegaussingTo adjust Advanced menu item Reduces picture noiseAdjusting screen aspect Picture stillnessSound adjustment Sound adjustmentPreset sound mode selection Stereo functionTimer setting Timer settingMaking use of Sleep timer function Making use of Timer menuSystem setup System setupSetting the menu background To select the language for the OSDAuto-Power-Off function Power Restore functionOperation in Video mode AV1/AV2/AV3/YCbCrOperations in Hdtv mode Making use of the Adjust sub-menu to adjust pictureOperation in Hdtv mode Buttons functionButtons function OSD menu introduction OSD menu overviewOSD menu introduction & Operation examples Contrast/brightness adjustment To switch between text mode and image modeOperation examples Screen adjustment Operations examplesFunction menu items selection Display mode setting Mode Input SignalTroubleshooting Guide Symptoms Check the following itemsSpecifications MonitorWhole unit Australia 1300 657