Memorex MVR2040-A Special Playback, To Visually Search for Desired Points, Skip Search

Page 33

SPECIAL PLAYBACK

TO VISUALLY SEARCH FOR DESIRED POINTS

When either the F.FWD or REW button is pressed in the PLAYBACK mode, the speed search picture will appear. When pressed twice, the search picture will increase speed. Speed search time depends upon the speed used (SP, LP or SLP) during recording.To rewind or fast forward a tape, press the STOP button, and then press the REW or F.FWD button.

To visually search backward, press the REW button

To visually search forward, press the F.FWD button

once or twice in the PLAYBACK mode.

once or twice in the PLAYBACK mode.

REW

F.FWD

The REVEW indicator will light in the display about 4 seconds.

The CUE indicator will light in the display about 4 seconds.

Press the PLAY button to resume normal viewing speed.

Press the PLAY button to resume normal viewing speed.

ENGLISH

SKIP SEARCH

Press the SKIP SEARCH button in the PLAY mode. The VCR will search forward through approximately 60 seconds of the tape (e.g. unwanted commercial time) and then resume normal playback.

SKIP

SEARCH

The CUE 1 indicator will light in the display. (For example : 1 press).

TO WATCH A STILL PICTURE

Press the PAUSE/STILL button in the PLAYBACK mode.

PAUSE/STILL

The STILL indicator will light in the display about 4 seconds. Press the PAUSE/STILL button again to resume normal playback.

SLOW MOTION PLAYBACK

FRAME BY FRAME ADVANCE

Press the SLOW button in the PLAYBACK mode. Playback will proceed at 1/10th of the normal speed.

SLOW

The SLOW indicator will light in the display about 4 seconds. Press the PLAY button again to resume normal playback.

NOTE: SLOW TRACKING AND VERTICAL LOCK ADJUSTMENT

If noise bars appear in the picture during slow motion, press the Manual TRACKING + or – button to reduce the noise bars. If the still picture jitters excessively, press the Manual TRACKING + or – button to stabilize the still picture.

Press the SLOW button during STILL playback.

SLOW

The still picture will advance by one frame each time you press the button. Hold the button for continuous frame by frame viewing.

Press the PAUSE/STILL button again to resume normal playback.

NOTES: • Best results during speed search playback can be obtained with cassette tapes recorded in the "SP"and"SLP" mode.

•The audio output is muted during SPEED SEARCH and STILL.

•A few noise bars will appear on the picture during SPEED SEARCH ,STILL, FRAME ADVANCE and SLOW MOTION.

•To prevent damage to the tape, CUE, REVIEW and STILL playback is automatically changed to the PLAYBACK

mode after 5 minutes.

33

 

4C80401A-E(P30-33)

33

25/2/99, 21:28

Page 32 Page 34
Image 33
Page 32 Page 34
Contents MVR2040A English Accessories CleaningPower Sources Read InstructionsPower Lines POWER-CORD ProtectionDamage Requiring Service Replacement PartsSafety Check Wall or Ceiling MountingHeat Features Table of Contents When YOU Experience the Above Conditions PrecautionsMoisture Condensation Moisture will Condense on the Unit in the Following CasesAvoid extreme moisture and dust Location of Controls FrontDescription of Controls AC Power Cord Connect to a 120V 60Hz outlet Location of Connectors RearFluorescent Display Tape SpeedDescription of Buttons Remote ControlBattery Cautions Battery InstallationEffective Distance of the Remote Control FeetAntenna to VCR Connection Basic ConnectionsEnglish VCR to TV Connection Splitter OHM Input 75/300 OHM Outputs VCR Incoming Cable Catv Cable TV ConnectionsAllows For basic cable service, no premium scrambled channelsVCR Splitter Recording scrambled channels AUDIO/VIDEO Connections AUDIO/VIDEO ConnectionStereo Amplifier Connections Setting the Video Channel Switch Rear of the VCR toFor a push-button TV tuner Check Before YOU Begin ON-SCREEN Language SelectionTo make any adjustments perform steps 2 through Setting the ClockTo select the Clock SET Option, then pressUP option, then press the Enter button Setting the ChannelsAutomatic Memory Tuning CH Memory mode, then press the EnterButton To ADD/DELETE Channels Using the SET + or buttonMode, then press Channel from memoryTurn on the VCR Power button Noise Elimination Blue ScreenPress the TV/VCR selector button to select Loading and Unloading Video Cassette Tapes LoadingUnloading To Start Playback Tapes PlaybackTo Stop Playback To play a prerecorded cassette tapePlayback To Rewind or Forward the Tape RapidlyFORWARD/REVERSE Picture Search To Visually Search for Desired Points Special PlaybackSkip Search To Watch a Still PictureTo Watch a Tape Repeatedly Over and over until the repeat mode is canceledRepeat option PositionRecording and Viewing the Same TV Program Recording a TV ProgramTab intact VCR will automatically turn onTo Stop Recording Temporarily To Stop RecordingPress the REC/OTR button Press the Stop button to stop recordingWill continue While the VCR is recording, press the TV/VCR3 hours HoursMenu Enter Setting the Timer RecordingCH 125 or To Correct the Settings
Top Page Image Contents