Memorex MT2252S MT2271S Lightning, Power Lines, Overloading, Object and Liquid Entry, Servicing

Page 3

13.LIGHTNING

To protect your unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

14.POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

15.OVERLOADING

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

16.OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17.OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding elec- trodes, and requirements for the grounding electrode.

18.SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.DAMAGE REQUIRING SERVICE

Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the unit.

c.If the unit has been exposed to rain or water.

d.If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

e.If the unit has been dropped or the cabinet has been damaged.

f.When the unit exhibits a distinct change in performance, this indicates a need for service.

20.REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

21.SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

22.WALL OR CEILING MOUNTING

If mounting this unit to a wall or ceiling follow the installation recommended by the manufacturer of a mounting bracket specifically designed for this type of product. Use only a mounting device that can handle the weight and size of your unit. Should your bracket require drilling holes into this unit, this would void the manufacturers warranty.

23.HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

24.NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelinesorf proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE

 

ANTENNA LEAD IN WIRE

GROUND CLAMP

 

 

ANTENNA DISCHARGE UNIT

ELECTRIC

(NEC SECTION 810-20)

 

SERVICE

GROUNDING CONDUCTORS

EQUIPMENT

(NEC SECTION 810-21)

 

GROUND CLAMPS

NEC-NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING ELECTRODE SYSTEM

S2898A

(NEC ART 250, PART H)

3

ENGLISH

3L40901A-E

3

11/3/2002, 12:04

Image 3
Contents MT2252S MT2271S Powercord Protection CleaningAccessories Power SourceSafety Check Power LinesDamage Requiring Service Replacement PartsFeatures Location of ControlsFront Back Remote Control HOW to Install BatteriesBattery Precautions TV/AV Selection ANTENNA/CATV ConnectionsAudio / Video Jack Connections Setting LanguageTo ADD/DELETE Channels To Memorize ChannelsAutomatic Channel Memory TV/CATV SelectionMovie Rating Setting V-CHIPClosed Caption TV RatingSound Adjustments Adjusting PictureStereo and Separate Audio Program SAP Model MT2252S MT2271S Troubleshooting GuideAccessories Symptoms Possible SolutionsMemo Memo Para SU Seguridad Instalacion EN Pared O Techo Caracteristicas Ubicacion DE LOS ControlesDelantera Trasera Control Remoto Como Instalar LAS PilasPrecauciones Para LAS Pilas Conexiones DE Antena Conexiones DE Toma AUDIO/VIDEOSeleccion TV/AV Nota Conexiones DE LA Toma DE Audio / Video Continuació NAjuste DE Lengua Operacion DEL TelevisorPara AÑ ADIR/BORRAR Canales Para Memorizar CanalesMemoria Automatica DE Canal Seleccion DE TV/CATVNotas Seleccion DE ChipProhibicion DE TV Prohibicion DE PeliculasPrograma DE Audio Separado SAP Y Estereo Ajustes DE SonidoAjuste DE Imagen Modelo MT2252S MT2271S Antes DE Solicitar ServicioEspecificaciones Sintoma Posible Solucion3L40901A L 02/04