Marantz PD4220V To avoid damage and prolong operating life, Plasma monitor cleaning procedure

Page 4

To avoid damage and prolong operating life:

1.Use only with 120V 50/60Hz AC power supply. Continued operation at line voltages greater than 120 Volts AC will shorten the life of the unit, and might even cause a fire hazard.

2.Handle the unit carefully when installing it and do not drop.

3.Set the unit away from heat, excessive dust, and direct sunlight.

4.Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the power cord and have it serviced by an authorized Service Center.

5.Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.

6.For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.

7.As is the case with any phosphor-based display (like a CRT monitor, for example) light output will gradually decrease over the life of a Plasma Display Panel.

8.To avoid sulfurization it is strongly recommended not to place the unit in a dressing room in a public bath or hot spring bath.

Plasma monitor cleaning procedure:

1.Use a soft dry cloth to clean the front panel and bezel area. Never use solvents such as alcohol or thinner to clean these surfaces.

2.Clean plasma ventilation areas with a vacuum cleaner with a soft brush nozzle attachment.

3.To ensure proper ventilation, cleaning of the ventilation areas must be carried out monthly. More frequent cleaning may be necessary depending on the environment in which the plasma monitor is installed.

Recommendations to avoid or minimize phosphor burn-in:

Like all phosphor-based display devices and all other gas plasma displays, plasma monitors can be susceptible to phosphor burn under certain circumstances. Certain operating conditions, such as the continuous display of a static image over a prolonged period of time, can result in phosphor burn if proper precautions are not taken. To protect your investment in this plasma monitor, please adhere to the following guidelines and recommendations for minimizing the occurrence of image burn:

*Always enable and use your computer’s screen saver function during use with a computer input source.

*Display a moving image whenever possible.

*Change the position of the menu display from time to time.

*Always power down the monitor when you are finished using it.

If the plasma monitor is in long term use or continuous operation take the following measures to reduce the likelihood of phosphor burn:

*Lower the Brightness and Contrast levels as much as possible without impairing image readability.

*Display an image with many colors and color gradations (i.e. photographic or photo-realistic images).

*Create image content with minimal contrast between light and dark areas, for example white characters on black backgrounds. Use complementary or pastel color whenever possible.

*Avoid displaying images with few colors and distinct, sharply defined borders between colors.

* Note: Burn-in is not covered by the warranty.

Contact Marantz Service Center for other recommended procedures that will best suit your particular application needs.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model PD4220V User Guide Features you’ll enjoy include Contents of the PackageIntroduction Introduction to the Plasma MonitorImportant Information PrecautionsRisk of Electric Shock Do not Open To avoid damage and prolong operating life Plasma monitor cleaning procedureRecommendations to avoid or minimize phosphor burn-in Recommandations importantes PrécautionsMises en garde et précautions de sécurité Risque D’ELECTROCUTIONMéthode de nettoyage du moniteur à plasma Contents How to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingTurns the monitor’s power on and off Receives the signals from the remote controlPart Names and Function Front ViewConnect the included power cord here Syncronization signalRear View/ Terminal Board Connect DVD’s, High Definition or Laser Discs, etc. hereRemote Control Battery Installation and Replacement Transmits the remote control signalsNot functional for the models covered in this manual Clears the number set by the ID Select buttonUsing the wired remote control mode Handling the remote controlOperating Range Approx 7m/23ftDigital signal output InstallationPersonal computer with a Connecting Your Document Camera Connecting Your VCR or Laser Disc PlayerConnecting Your DVD Player Connections with Equipment that have a Digital InterfacePin Assignments and Signal Levels for 15 pin RGB Analog Pin No Signal AnalogCreating a video wall Cable ManagementBasic Operations To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining timeWhen viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When Picture Size is set to OFF Supported resolution  Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the pictureAdjusting the color to the desired level Setting the color temperatureReducing noise in the picture Making the Low Tone adjustments  Adjusting the white balance Gamma settings  LOW Tone settingsAudio Settings Menu Adjusting the colors Color Tune settings  Audio settings menuImage Adjust Settings Menu Setting the allocation of the audio connectorsAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen  OSM Orbiter settingsSetting high definition images to the suitable screen size Setting the Input Skip Input Skip settings  RGB Select modesResetting to the default values Option2 Settings MenuSetting the power management for computer images POWER/STANDBY indicator Setting the picture to suit the moviePLE settings Reducing burn-in of the screenOrbiter Function settings Orbiter settingsInverse Settings To select on for the Working Time Setting the timeScreen Wiper Setting the screen size for S1/S2 video input Soft Focus settingsSetting the gray level for the sides of the screen Gray Level settingsSetting the picture size for RGB input signals Setting the signal and black level for DVI signalS1/S2 settings PLUG/PLAY settingsOption3 Settings Menu Using the timerPresent Time settings Present TimeSetting the power on mode To reset the programTo reset the data Special characters in the Program Timer screenEnabling/disabling remote control wireless transmission PWR. on Mode settingsControl Lock settings IR Remote settingsLoop Out setting ID number settingVideo Wall setting Divider settingsVideo Wall Position settings ScreensDISP. Mode settings Auto ID settingsImage Adjust settings On Delay Power on delay On Delay settingsPLE Link settings PLE LinkAdvanced OSM Settings Menu Setting the menu modeRepeat Timer Repeat Timer settingsLanguage Settings Menu Color System Settings MenuSetting the language for the menus Setting the video signal formatExternal Control ApplicationConnections Communication ParametersTroubleshooting Symptom Checks RemedyPage Page Model PD4220V Information Page DVI cable not supplied Band DOC avis de conformation AvertissementRemarque RGB SpecificationsDVD/HD/DTV Page Table of Signals Supported  42Wide VGA Supported resolutionComputer input signals supported by this system Full DVI05BW851010 7S900058 04/2004 ECMar Is a registered trademark Japan
Top Page Image Contents