Marantz PD4220V manual 05BW851010 7S900058 04/2004 ECMar

Page 59

*1 Only when using a graphic accelerator board that is capable of displaying 852480.

*2 Display only 400 lines (42Wide VGA) with the screen center of the vertical orientation located at the center.

*3 The picture is displayed in the original resolution. The picture will be compressed for other signals.

*4 Aspect ratio is 5:4. This signal is converted to the following signal (42Wide VGA: 600 dots480 lines).

*5 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the RGB mode prepared for the input signals listed in the table above.

*6 To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.

*7 Other screen modes (ZOOM and STADIUM) are available as well.

*8 When viewing a moving picture at a vertical frequency greater than 65Hz, the picture may sometimes be unstable (jumpy). If this occurs, please set the refresh rate of the external equipment to 60Hz.

To view 480I@60Hz (480 interlaced lines, 60Hz refresh rate) or 576I@50Hz (567 interlaced lines, 50Hz refresh rate) when sync polarity is “Sync on Green”, set “RGB SELECT” to “MOTION”.

NOTE:

•While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the picture or the fine picture because of errors in synchronization of your computer.

•This monitor has a resolution of 853 dots480 lines. It is recommended that the input signal should be VGA, wide VGA, or equivalent for PD4220V.

•With digital input some signals are not accepted.

•The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

•If you are connecting a composite sync signal, use the HD terminal.

•“IBM PC/AT” and “VGA” are registered trademarks of International Business Machines, Inc. of the United States.

•“Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.

Printed in Japan

05BW851010

7S900058

04/2004 ECMar

Image 59

Contents Model PD4220V User Guide Introduction to the Plasma Monitor Features you’ll enjoy includeContents of the Package IntroductionRisk of Electric Shock Do not Open PrecautionsImportant Information Recommendations to avoid or minimize phosphor burn-in Plasma monitor cleaning procedureTo avoid damage and prolong operating life Risque D’ELECTROCUTION Recommandations importantesPrécautions Mises en garde et précautions de sécuritéMéthode de nettoyage du moniteur à plasma Contents Ventilation Requirements for enclosure mounting How to Attach Options to the Plasma MonitorFront View Turns the monitor’s power on and offReceives the signals from the remote control Part Names and FunctionConnect DVD’s, High Definition or Laser Discs, etc. here Connect the included power cord hereSyncronization signal Rear View/ Terminal BoardRemote Control Clears the number set by the ID Select button Battery Installation and ReplacementTransmits the remote control signals Not functional for the models covered in this manualApprox 7m/23ft Using the wired remote control modeHandling the remote control Operating RangePersonal computer with a InstallationDigital signal output Connections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallBasic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Supported resolutionMenu Operations Advanced menu modeMenu Tree ResetOPTION2 PWR. MGT Adjusting the picture Picture Settings MenuReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level LOW Tone settings Making the Low Tone adjustments Adjusting the white balance Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors Color Tune settingsExample Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip Input Skip settingsSetting the power management for computer images Option2 Settings MenuResetting to the default values Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie PLE settingsInverse Settings Orbiter settingsOrbiter Function settings Screen Wiper Setting the timeTo select on for the Working Time Gray Level settings Setting the screen size for S1/S2 video inputSoft Focus settings Setting the gray level for the sides of the screenPLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settingsPresent Time Option3 Settings MenuUsing the timer Present Time settingsSpecial characters in the Program Timer screen Setting the power on modeTo reset the program To reset the dataIR Remote settings Enabling/disabling remote control wireless transmissionPWR. on Mode settings Control Lock settingsID number setting Loop Out settingScreens Video Wall settingDivider settings Video Wall Position settingsImage Adjust settings Auto ID settingsDISP. Mode settings PLE Link On Delay Power on delayOn Delay settings PLE Link settingsRepeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat TimerSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters External ControlApplication ConnectionsSymptom Checks Remedy TroubleshootingPage Page Model PD4220V Information Page DVI cable not supplied Band Remarque AvertissementDOC avis de conformation DVD/HD/DTV SpecificationsRGB Page Full DVI Table of Signals Supported 42Wide VGA Supported resolution Computer input signals supported by this system05BW851010 7S900058 04/2004 ECMar Japan Is a registered trademark