Marantz PD4220V manual How to Attach Options to the Plasma Monitor

Page 8

How to Attach Options to the Plasma Monitor

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

*While it is upright. (See Drawing A)

*As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

*Do not touch or hold the screen face when carrying the unit.

This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall mount unit, Stand, etc.)

* See the inside of the cover page.

For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.

Product warranty does not cover damage caused by improper installation.

* Use only the mounting kit or stand provided by manufacturer and listed under Options.

Drawing A

Drawing B

Some models are equipped with handles.

When installing or carrying, use the handles attached to the upper back of the display.

Ventilation Requirements for enclosure mounting

To allow heat to disperse, leave space between surrounding objects as shown on the diagram below when installing.

 

Wall

 

50mm (2")

50mm (2")

(2")

 

 

mm

Wall

50

 

 

 

 

 

 

 

 

 

 

 

How to use the safety metal fittings and the screws for safety metal fittings

These are fittings for fastening the unit to a wall to prevent tipping due to external shock when using the stand (optional). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws. * Safety metal fittings will differ according to the model.

Screw hole

Screw or Hook etc. (Not supplied)

50mm (2") (2")mm 50

Safty metal fittings

Screw for Safty metal fittings

Metal chain (Not supplied)

Wall

Table Top

1

Image 8
Contents Model PD4220V User Guide Features you’ll enjoy include Contents of the PackageIntroduction Introduction to the Plasma MonitorRisk of Electric Shock Do not Open PrecautionsImportant Information Recommendations to avoid or minimize phosphor burn-in Plasma monitor cleaning procedureTo avoid damage and prolong operating life Recommandations importantes PrécautionsMises en garde et précautions de sécurité Risque D’ELECTROCUTIONMéthode de nettoyage du moniteur à plasma Contents How to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingTurns the monitor’s power on and off Receives the signals from the remote controlPart Names and Function Front ViewConnect the included power cord here Syncronization signalRear View/ Terminal Board Connect DVD’s, High Definition or Laser Discs, etc. hereRemote Control Battery Installation and Replacement Transmits the remote control signalsNot functional for the models covered in this manual Clears the number set by the ID Select buttonUsing the wired remote control mode Handling the remote controlOperating Range Approx 7m/23ftPersonal computer with a InstallationDigital signal output Connecting Your Document Camera Connecting Your VCR or Laser Disc PlayerConnecting Your DVD Player Connections with Equipment that have a Digital InterfacePin Assignments and Signal Levels for 15 pin RGB Analog Pin No Signal AnalogCreating a video wall Cable ManagementBasic Operations To set the off timer To cancel the off timerAfter the power is turned off with the off timer To check the remaining timeWhen viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When Picture Size is set to OFF Supported resolution  Picture Size setting Advanced menu mode Menu OperationsReset Menu TreeOPTION2 PWR. MGT Picture Settings Menu Adjusting the pictureReducing noise in the picture Setting the color temperatureAdjusting the color to the desired level Making the Low Tone adjustments  Adjusting the white balance Gamma settings  LOW Tone settingsAudio Settings Menu Adjusting the colors Color Tune settings  Audio settings menuImage Adjust Settings Menu Setting the allocation of the audio connectorsAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to VideoOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen  OSM Orbiter settingsSetting high definition images to the suitable screen size Setting the Input Skip Input Skip settings  RGB Select modesSetting the power management for computer images Option2 Settings MenuResetting to the default values POWER/STANDBY indicator Setting the picture to suit the moviePLE settings Reducing burn-in of the screenInverse Settings Orbiter settingsOrbiter Function settings Screen Wiper Setting the timeTo select on for the Working Time Setting the screen size for S1/S2 video input Soft Focus settingsSetting the gray level for the sides of the screen Gray Level settingsSetting the picture size for RGB input signals Setting the signal and black level for DVI signalS1/S2 settings PLUG/PLAY settingsOption3 Settings Menu Using the timerPresent Time settings Present TimeSetting the power on mode To reset the programTo reset the data Special characters in the Program Timer screenEnabling/disabling remote control wireless transmission PWR. on Mode settingsControl Lock settings IR Remote settingsLoop Out setting ID number settingVideo Wall setting Divider settingsVideo Wall Position settings ScreensImage Adjust settings Auto ID settingsDISP. Mode settings On Delay Power on delay On Delay settingsPLE Link settings PLE LinkAdvanced OSM Settings Menu Setting the menu modeRepeat Timer Repeat Timer settingsLanguage Settings Menu Color System Settings MenuSetting the language for the menus Setting the video signal formatExternal Control ApplicationConnections Communication ParametersTroubleshooting Symptom Checks RemedyPage Page Model PD4220V Information Page DVI cable not supplied Band Remarque AvertissementDOC avis de conformation DVD/HD/DTV SpecificationsRGB Page Table of Signals Supported  42Wide VGA Supported resolutionComputer input signals supported by this system Full DVI05BW851010 7S900058 04/2004 ECMar Is a registered trademark Japan