FUNAI CIWP4206 A owner manual Miscellaneous

Page 33

Symptom

 

Remedy

Ghosts in picture

 

• Check the antenna or cable connection to the main unit.

 

 

• When the outside antenna is used, check the wire condition and

 

 

connection.

 

 

• Electrical interference from nearby appliances may affect picture

 

 

quality.

 

 

• View other TV channels. The problem might be limited to the

 

 

broadcasting station.

 

 

 

Bars on screen

 

• When the outside antenna is used, check the wire condition and

 

 

connection.

 

 

• Electrical interference from nearby appliances may affect picture

 

 

quality.

 

 

 

Picture rolls vertically

 

• When the outside antenna is used, check the wire condition and

 

 

connection.

 

 

• Electrical interference from nearby appliances may affect picture

 

 

quality.

 

 

• View other TV channels. The problem might be limited to the

 

 

broadcasting station.

 

 

 

Different color marks on screen

 

• Move your TV away from nearby electric appliances. Turn off the

 

 

power and wait 30 minutes before turning it back on.

 

 

• View other TV channels. The problem might be limited to the

 

 

broadcasting station.

Poor reception on some channels

 

• Check the antenna or cable connection to the main unit.

 

 

• When the outside antenna is used, check the wire condition and

 

 

connection.

 

 

• Electrical interference from nearby appliances may affect picture

 

 

quality.

 

 

• View other TV channels. The problem might be limited to the

 

 

broadcasting station.

 

 

 

Picture OK, sound poor

 

• Electrical interference from nearby appliances may affect picture

 

 

quality.

 

 

• View other TV channels. The problem might be limited to the

 

 

broadcasting station.

 

 

 

MISCELLANEOUS

Burn-in on screen

• Do not continuously display images such as video games, com-

 

puter graphics, stock market quotations or other fixed patterns.

 

Those images may cause screen burn-in.

 

If burn-in occurs, display a movie or TV show to reduce the

 

problem.

 

These images can cause permanent damage to your screen.

 

Burn-in caused by misuse is not covered by your warranty.

 

 

No reception of digital signals

• Make sure Autoscan has been completed (Refer to “AUTOSCAN” on

 

page 14). Autoscan must be completed when you set up your TV for

 

the first time or move it to a location where previously unavailable

 

channels are broadcast.

 

• The selected channel may not be broadcasting.

 

• When Autoscan is interrupted, some channels will not be

 

received. Make sure to complete Autoscan in the setup screen.

 

 

Channel changes automatically

• Many digital channels have alternate channel numbers. TV changes the

 

numbers automatically to the ones signifying the broadcasting stations.

 

These are the numbers used for analog broadcasts.

 

 

Remote Control doesn’t work

• Check the antenna or cable connection to the main unit.

 

• Check the batteries of the remote control.

 

• Check if there is an obstacle between the sensor and the

 

remote control.

 

• Test the signal output. If OK, there might be remote sensor trou-

 

ble. (Refer to “IR SIGNAL CHECK” on page 36.)

 

 

33

EN

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Inch Do not install near any heat sources such as Clean only with dry clothDo not defeat the safety purpose of the polar Prong are provided for your safety. If the providImportant Safety Instructions / Precautions Precautions# Caution Dealer Purchase fromFeatures Supplied AccessoriesDTV/TV/CATV ChipContents Input SELECT/ENTER Functions Remote CONTROL, Control and Rear Panel FunctionAbout Interference to Infrared Devices About Pixel DefectsRemote Control Range Installing the BatteriesBattery Precautions FunctionsPreparation for USE Connection Antenna Cable ConnectionConnection to CABLE/SATELLITE BOX Hdmi Connecting Other DevicesVideo Cable Connection Component Cable ConnectionPreparation For USEVideo Connection Digital Audio ConnectionAnalog Audio Connection Connecting the Power CableInitial Settings Initial Settings Initial SetupSelect source of ANT. in jack using K/L, press Enter Autoscan will start automaticallyFor TV channels, using K / L , select Air Channel Settings AutoscanFor Catv channels, select Cable Press EnterSelect Register with Enter To exit the setup, press Setup To exit the setup, press SetupChannel List Manual RegisterDisplays signal strength for each channel Antenna ConfirmationAntenna Language Selection Setting the Panel SaverLanguage DetaililWatching TV Channel Selection Volume AdjustmentNtsc AtscStill Mode Selecting Audio ChannelsWatching TV Accessing External Devices Full SidebarCinema WideScreen Information To clear the display, press Back or Info againBuffy Vampire i Slayer l Optional Settings Setup Screen Sleep TimerWatching TV / Optional Settings Refer to Language Selection onPicture Adjustment Closed Caption Caption Mode CC1 and Text1CC3 and Text3 CC2, CC4, Text2 and Text4Enter to confirm DTV Closed Caption Closed Caption StyleClosed l Caption CC Style leOptional Settings Password entry screen is displayed Using K / L , select V-chipChip Use the Number buttons and enter the 4-digit numberNC-17 SelectionPG-13 TV-MA Mature audience only TV-14Chipip Enter password Confirm password Hdmi AudioSet the method of sound input for Hdmi jack Optional Settings / Attaching a Wall Mount Bracket Attaching a Wall Mount Bracket Sold SeparatelySold Separately Miscellaneous Troubleshooting Guide Miscellaneous Logue Captions are delayed behind the diaDepending on the screen ContentsGlossary MaintenanceMiscellaneous / Specifications SpecificationsVHF UHF CatvWarranty Statement Regarding NON Authorized Repairs DurationLimits and Exclusions 2AUDIO Output Connection Video or Video Connection1ANTENNA 3HDMI Connection 4COMPONENT Connection Plasma Display TV rear sidePlasma Display TV side view VCR
Top Page Image Contents