Pioneer PRO 510HD Panel frame Side view Screws, Upper frame cover, Frame cover Lower frame cover

Page 11

3.While holding the screen in place, attach the upper panel frame to the screen and fasten five or three screws starting with the center screw.

Do not overtighten the screws.

Overtightened screws may cause the protective screen to warp.

Panel frame

Side view

Screws

Five screws type

Panel frame

Side view

Screws

Three screws type

4.Attach side frame covers:

1)Peel off adhesive strip from rear side of the frame cover.

2)Attach side frame cover along the aluminium edge guards leaving a space of approximately 0 to 1/32 in. (0 to 1 mm) from the upper panel frame.

Upper panel frame

Screen frame

Screen frame

Upper panel

 

 

 

 

frame

 

0 to 1 mm

 

(0 to 1/32 in.)

 

Side frame cover

Side frame

 

cover

 

INSTALLING THE MONITOR

5.Attach the remaining frame covers to the upper and lower panel frames: first, insert the edge of the frame cover into the outer groove of the panel frame, then starting at one end, push the inner part of the frame cover over the inner edge of the panel frame snapping it into place.

Upper frame cover

Remove

Attach

Frame cover

Lower frame cover

HOW TO REMOVE THE PROTECTIVE SCREEN

1)First, remove the frame covers only from the upper and lower panel frames. Care must be taken to avoid scratching the protective screen or frame covers.

2)Remove the screws from the upper panel frame and remove the upper panel frame.

3)Remove the protective screen from the lower panel frame and remove the lower panel frame. Reattach panel frames and frame covers as indicated in HOW TO ATTACH UPPER AND LOWER TRIM ONLY.

NOTES FOR CARE AND CLEANING OF SCREEN:

•Do not hit or throw anything onto the protective screen, as a damaged protective screen may cause injury.

•If the protective screen surface is dirty, wipe it with a cloth dipped in warm water with mild detergent and then wrung out. Wipe it dry with a soft, dry cloth.

•Never use paint thinner or other cleaners to clean the protective screen as they may contain harmful chemicals that will damage the finish of the screen.

INTRODUCTION

11

<ARB1527>

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PRO-610HDPRO-510HD Dual Tuner Split screen and Search screen function Fully Illuminated Remote Control UnitProgressive Scan/HDTV Ready Dual System Component Input for NTSC/ ProgressiveImportant Notice IntroductionFor Your Personal Safety Important Safety Instructions and WarningsProtection and Location of Your Projection Monitor Receiver For Servicing and Modification Operation of Your Projection Monitor ReceiverContents Buttons operated ARB1527 HOW to Read this Operating InstructionsFunction on this Select TVCare of Your Projection Monitor Installing the MonitorInstallation Precautions Operating PrecautionsPanel frame Protective screen HOW to Attach the Provided Protective ScreenPartsincludedforprotectivescreeninstallation Panel Frames Mounts Side Frame Covers TrimsFrame cover Lower frame cover Panel frame Side view ScrewsUpper frame cover Before USE Before you watch the TV, perform the following procedureBasic Operations Inserting batteries into the remote control unitRemote control operation range Battery replacementConnecting the Catv converter Connecting the AntennaConnecting VHF/UHF antenna Connecting VHF/UHF antenna with VCRCable TV Catv converter Connecting the Catv converter with VCRConnecting VHF/UHF antenna and Catv converter VHF antenna UHF antenna MixerVideo movie, etc SAT tuner Digital tuner DVD/LD playerRear panel SignalComponent Video Input jack Input jacksMonitor Output jacks Video Input jacksVIDEO/VIDEO RGB Front Panel Functions Input 4 jacks Volume buttonsReturn button Remote Control Unit Functions = CH Enter button VOL volume +, buttonsSPLIT/SEARCH screen buttons Display buttonSelect by pressing the number button Example Turn on the Main Power switchTo Watch TV Best Horizontal and Vertical Viewing AngleCable Catv Channel Assignment Table Auto power off functionBasic OperationsChecking the Menu Picture adjustment menu SeeSound adjustment menu See SET UP menu See pages 28, 30, 33, 36, 43, 59, 62 Screen setting menu SeeENTER. Refer to Auto Channel PresetSelect TV The5orbuttonandthenpressingSET∙ Auto Channel Preset starts Select Auto Preset StartAfter setting, press Menu to turn the menu off The5orbuttonandthenpressingSET Convergence AdjustmentSelect screen mode When the cross pattern is whiteMove the red line onto the green line TV-Y TV-Y7 RatingNo ONE 17 and Under Admitted Not RatedSelect Program Block in the same Setting the Program Blocking LevelGuidelines Set Block to onBlock Removing Blocking MULTI-SCREEN ModeBasic Functions Cut along dotted line and file after reading Changing Password5or buttonandthenpressingSET Enter new password Natural Wide Cinema Wide Normal Full Zoom Setting Screen ModePress the Screen Mode button Changing Screen Size∙ Adjustable range Cinema Wide mode To Adjust the Screen PositionAdjust the screen position After adjusting, press Menu to turn the menu offPress the Freeze button Making Notes on Program Content Freeze screenMULTI-SCREEN Function Press the Split buttonSearch screen FunctionsPress the Search button Set CC to on Select ModeSelect Channel ADD/DEL Changing Channel SET UPTo ADD or Delete Preset Channels Channel PresetSelect Channel ,thenselectachannel Select Setting , then select ADD addition or DEL deletionOther channels Select Label and input the label charactersTo set Favorite Channel SET UPSelect Favorite Channel Select the channel Select numberSelect antenna Recall the Desired Settings Picture AdjustmentsPress Menu and select Picture Storing the SET Picture Quality in MemorySelect the input source and show the image on the screen Refer to To Adjust the Picture QualitySelect the adjustment item Adjust by pressing 2orSelect the desired level To adjust 3D Y/C LevelPress Menu and select Picture . Refer to Select Other Select 3D Y/C LevelSelect Color Temp To adjust 3D NR LevelTo adjust Color Temperature Select 3D NR LevelSelect Flesh Tone To adjust Flesh ToneTo adjust Purecinema Select SVM To adjust Scan Velocity ModulationSelect the desired Purecinema mode ENTER. Refer to Select MTS in the same way Sound AdjustmentsSelect the desired audio mode Watching Stereo and Bilingual ProgramsBASS, Treble and Balance can be adjusted To Adjust the Sound QualitySelect the adjustment item Adjust by pressing 2orSelect Surround To Select the Desired Surround ModeSelect the desired Surround mode After setting, press Menu to turnSet Super Bass to on To Adjust Super BassUse this function to enjoy powerful bass sounds Select Super BassMenu off DPO FunctionSelect DPO in the same way Set DPO to onSelect ADJ MULTI-POINT Select the adjust pointAdjust the red line Convergence adjustment may be fined-tuned from hereAdjust the blue line Receiver Audio SignalConnection with Receiver CATVconverterSelect Speaker Select the Speaker modeVarious Functions Select Audio OUT Select the Audio OUT modeCatv Signal InputUnless required, set the System Mode to OFF Press Menu and select SET UPSelect System Mode Switch the System ModeTo other units bearing the ë mark Connecting the System Remote∙ Example To select DVD/LD Remote Code SET UPAt the same time, press the Edit button and number button Select the desired manufacturerManufacturers preset remote control signals LED will remain lit To Learn Remote Control SignalsExample To learn the VCR power to turn on Before operationVCR SET/ENTER, TV/SAT/DVDTV/SAT/DVD MENU, DTV/DVD TOP MenuReceiver Control Buttons Using the TV Remote Control Unit to Control Other DevicesRemote Control Unit Setting Buttons DTV Control Buttons CH channel +, buttons Source Power buttonTurns the power of the cable converter on and off Cable Control ButtonsSAT Info button SAT Control ButtonsSAT Menu button SAT Guide buttonÁFF button VCR Control Buttons7STOP button VCR REC record buttonDVD/LD Control Buttons Connect the digital tuner Set the mode switch to TV/DTV and then press the DTV buttonInitial setting To Watch DTVDigital tuner SH-D09 Channel scan has finished You have completed the initial settingsOthers Digital broadcast channels Select a channel∙ Press the button between the main and sub channels There are four methods for thisExample Channel DTV Outputs Recording DTV ProgramsRecording Menu off Signals will then be output fromOn pages 78 to ENTER. Refer to Select DTV OUT in the same wayConnection with Receiver Connect the VHF/UHF signal to the digital tunerWill switch between DTV and TV mode. To change the input Set the System Mode to ON. Refer to∙ Switching the monitor to DTV mode makes it possible to ∙ Each time the DTV button is pressed, the operating modeClosed Caption menu See SET UP menu SeeMenu Index Main menu SeeConvergence menu See pages 30 Channel SET UP menu SeeChange Password menu See Auto Channel Preset menu SeeSymptom CAUSE/REMEDY Pages TroubleshootingSymptom Cause Specifications Others 99I00SF0W00 0 4 2 1 1 4 0
Related manuals
Manual 83 pages 976 b

PRO 510HD, PRO-610HD specifications

The Pioneer PRO-510HD and PRO-610HD are two advanced professional display monitors that exemplify cutting-edge technology in the realm of high-definition visual solutions. Designed for various applications, including broadcasting, live events, and video production, these monitors provide exceptional image quality and versatile features.

One of the standout characteristics of both models is their high-resolution display capabilities. The PRO-510HD boasts a 51-inch screen size with an impressive resolution of 1920 x 1080 pixels, ensuring sharp and vibrant images that meet the demands of professional users. The larger PRO-610HD features a 61-inch screen size with the same high-definition resolution, allowing for an immersive viewing experience.

These monitors leverage advanced LCD technology to deliver remarkable color accuracy and consistent brightness. With a wide color gamut, users can expect true-to-life colors, making these monitors ideal for color-critical applications. The brightness levels of both models reach up to 700 cd/m², ensuring visibility even in brightly lit environments.

Connectivity is a crucial aspect of any professional monitor, and the PRO-510HD and PRO-610HD are equipped with a range of input options. They offer multiple HD-SDI, HDMI, DVI, and analog connections, allowing for seamless integration with various broadcasting and production equipment. This flexibility ensures that users can easily connect their devices without the need for additional converters or adapters.

Another significant feature of these monitors is the built-in waveform and vector scope displays. These tools are essential for ensuring proper exposure and color balance, providing users with real-time monitoring of their video signals. The monitors also support various aspect ratios, making it easy to adjust the display according to specific project requirements.

Durability is key for professional equipment, and both the PRO-510HD and PRO-610HD are constructed with robust materials, ensuring longevity even in demanding environments. The monitors are designed for continuous operation, making them reliable for long hours of use whether in studios or on location.

In conclusion, the Pioneer PRO-510HD and PRO-610HD are powerful tools for professionals who require high-quality displays with advanced features. Their excellent image quality, extensive connectivity options, and integrated monitoring tools make them an attractive choice for anyone involved in video production or broadcasting. With their durable design and user-friendly operation, these monitors stand out as reliable partners in the visual media landscape.
Top Page Image Contents