Pioneer PRO 510HD, PRO-610HD manual Return button, Volume buttons, Input 4 jacks

Page 21

8RETURN button

Press to set the Projection Monitor to its initial mode.

Initial mode

Input selector:

Set to TV.

TV channel:

Remains at the last channel set.

VOLUME:

Remains at the last setting.

MUTING:

OFF

PICTURE

 

MODE:

STD

Parameters:

Set to 0.

3D Y/C LEVEL:

3

3D NR LEVEL:

3

COLOR TEMP:

STD

FLESH TONE:

ON

PURECINEMA:

HQ

SVM

HIGH

SOUND

 

MTS:

MAIN

Parameters:

Set to 0.

SURROUND:

OFF

SUPER BASS:

OFF

SCREEN

 

MODE:

NATURAL WIDE

V. POSITION:

Set to 0.

CC:

OFF

DPO:

OFF

SYSTEM IN/OUT

 

SPEAKER:

NORMAL

AUDIO OUT:

FIXED

SYSTEM MODE:

OFF

DTV OUT:

OFF(WhentheSH-D09isconnected)

∙When this button is pressed while adjusting the MULTI- POINT convergence, the MULTI-POINT convergence returns to the initial mode.

9VOLUME buttons

Press plus (+) button to increase the volume, press minus (–) button to decrease it.

FRONT PANEL FUNCTIONS

0INPUT 4 jacks

These inputs are for Video Movie and VCR. Use RCA-type pin plug cords (the same as those used in Hi-Fi systems) and S- VIDEO cords for connections. When the audio source to be connected is monaural, connect the source to the L-(MONO) jack.

CAUTION:

Do not press any operation button on the Projection Monitor or the remote control unit while recording. Signals from the MONITOR OUTPUT jacks may be temporarily interrupted when a button is pressed.

ATTENTION

The Projection Monitor Receiver will not function properly in the following cases.

∙An electrical discharge in the CRT.

∙Lightning storms.

∙High static electricity environment.

∙Poor voltage regulation in the power source.

If the Projection Monitor does not operate properly, reset it as follows:

1.Turn off the power of the unit with the 4 MAIN POWER switch.

2.After approximately 1 minute, turn on the power with 4 MAIN POWER switch and 5 POWER button.

If the normal operation cannot be restored after the above treatment, immediately unplug the power cord and call your nearest PIONEER-authorized service center.

NOTE:

On rare occasions, an electrical discharge may occur inside the CRT. It makes a short, sharp pop and either no sound is produced or the volume level changes by itself. The SPLIT screen and SEARCH screen functions will be cancelled automatically if an electrical discharge occurs when this function is engaged.

BASIC OPERATIONS

90

S-VIDEO

VIDEO

L-AUDIO-R

 

(MONO)

VOLUME

INPUT 4

 

21

<ARB1527>

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PRO-610HDPRO-510HD Progressive Scan/HDTV Ready Fully Illuminated Remote Control UnitDual System Component Input for NTSC/ Progressive Dual Tuner Split screen and Search screen functionImportant Notice IntroductionFor Your Personal Safety Important Safety Instructions and WarningsProtection and Location of Your Projection Monitor Receiver For Servicing and Modification Operation of Your Projection Monitor ReceiverContents Function on this HOW to Read this Operating InstructionsSelect TV Buttons operated ARB1527Installation Precautions Installing the MonitorOperating Precautions Care of Your Projection MonitorPartsincludedforprotectivescreeninstallation HOW to Attach the Provided Protective ScreenPanel Frames Mounts Side Frame Covers Trims Panel frame Protective screenPanel frame Side view Screws Upper frame coverFrame cover Lower frame cover Before USE Before you watch the TV, perform the following procedureRemote control operation range Inserting batteries into the remote control unitBattery replacement Basic OperationsConnecting VHF/UHF antenna Connecting the AntennaConnecting VHF/UHF antenna with VCR Connecting the Catv converterConnecting VHF/UHF antenna and Catv converter Connecting the Catv converter with VCRVHF antenna UHF antenna Mixer Cable TV Catv converterVideo movie, etc SAT tuner Digital tuner DVD/LD playerRear panel SignalMonitor Output jacks Input jacksVideo Input jacks Component Video Input jackVIDEO/VIDEO RGB Front Panel Functions Volume buttons Return buttonInput 4 jacks Remote Control Unit Functions SPLIT/SEARCH screen buttons VOL volume +, buttonsDisplay button = CH Enter buttonTo Watch TV Turn on the Main Power switchBest Horizontal and Vertical Viewing Angle Select by pressing the number button ExampleBasic Auto power off functionOperations Cable Catv Channel Assignment TablePicture adjustment menu See Sound adjustment menu SeeChecking the Menu SET UP menu See pages 28, 30, 33, 36, 43, 59, 62 Screen setting menu SeeSelect TV Auto Channel PresetThe5orbuttonandthenpressingSET ENTER. Refer toSelect Auto Preset Start After setting, press Menu to turn the menu off∙ Auto Channel Preset starts Select screen mode Convergence AdjustmentWhen the cross pattern is white The5orbuttonandthenpressingSETMove the red line onto the green line No ONE 17 and Under Admitted RatingNot Rated TV-Y TV-Y7Select Program Block in the same Setting the Program Blocking LevelGuidelines Set Block to onRemoving Blocking MULTI-SCREEN Mode Basic FunctionsBlock Changing Password 5or buttonandthenpressingSETCut along dotted line and file after reading Enter new password Press the Screen Mode button Setting Screen ModeChanging Screen Size Natural Wide Cinema Wide Normal Full ZoomAdjust the screen position To Adjust the Screen PositionAfter adjusting, press Menu to turn the menu off ∙ Adjustable range Cinema Wide modeMULTI-SCREEN Function Making Notes on Program Content Freeze screenPress the Split button Press the Freeze buttonFunctions Press the Search buttonSearch screen Set CC to on Select ModeTo ADD or Delete Preset Channels Changing Channel SET UPChannel Preset Select Channel ADD/DELSelect Channel ,thenselectachannel Select Setting , then select ADD addition or DEL deletionOther channels Select Label and input the label charactersFavorite Channel SET UP Select Favorite ChannelTo set Select number Select antennaSelect the channel Recall the Desired Settings Picture AdjustmentsStoring the SET Picture Quality in Memory Select the input source and show the image on the screenPress Menu and select Picture Select the adjustment item To Adjust the Picture QualityAdjust by pressing 2or Refer toPress Menu and select Picture . Refer to Select Other To adjust 3D Y/C LevelSelect 3D Y/C Level Select the desired levelTo adjust Color Temperature To adjust 3D NR LevelSelect 3D NR Level Select Color TempTo adjust Flesh Tone To adjust PurecinemaSelect Flesh Tone To adjust Scan Velocity Modulation Select the desired Purecinema modeSelect SVM Select the desired audio mode Sound AdjustmentsWatching Stereo and Bilingual Programs ENTER. Refer to Select MTS in the same waySelect the adjustment item To Adjust the Sound QualityAdjust by pressing 2or BASS, Treble and Balance can be adjustedSelect the desired Surround mode To Select the Desired Surround ModeAfter setting, press Menu to turn Select SurroundUse this function to enjoy powerful bass sounds To Adjust Super BassSelect Super Bass Set Super Bass to onSelect DPO in the same way DPO FunctionSet DPO to on Menu offAdjust the red line Select the adjust pointConvergence adjustment may be fined-tuned from here Select ADJ MULTI-POINTAdjust the blue line Connection with Receiver Audio SignalCATVconverter ReceiverSelect the Speaker mode Various FunctionsSelect Speaker Select Audio OUT Select the Audio OUT modeCatv Signal InputSelect System Mode Press Menu and select SET UPSwitch the System Mode Unless required, set the System Mode to OFFTo other units bearing the ë mark Connecting the System RemoteAt the same time, press the Edit button and number button Remote Code SET UPSelect the desired manufacturer ∙ Example To select DVD/LDManufacturers preset remote control signals Example To learn the VCR power to turn on To Learn Remote Control SignalsBefore operation LED will remain litTV/SAT/DVD MENU, DTV/DVD TOP SET/ENTER, TV/SAT/DVDMenu VCRUsing the TV Remote Control Unit to Control Other Devices Remote Control Unit Setting ButtonsReceiver Control Buttons DTV Control Buttons Turns the power of the cable converter on and off Source Power buttonCable Control Buttons CH channel +, buttonsSAT Menu button SAT Control ButtonsSAT Guide button SAT Info button7STOP button VCR Control ButtonsVCR REC record button ÁFF buttonDVD/LD Control Buttons Initial setting Set the mode switch to TV/DTV and then press the DTV buttonTo Watch DTV Connect the digital tunerYou have completed the initial settings OthersDigital tuner SH-D09 Channel scan has finished Digital broadcast channels Select a channelThere are four methods for this Example Channel∙ Press the button between the main and sub channels DTV Outputs Recording DTV ProgramsOn pages 78 to Menu off Signals will then be output fromENTER. Refer to Select DTV OUT in the same way RecordingConnection with Receiver Connect the VHF/UHF signal to the digital tuner∙ Switching the monitor to DTV mode makes it possible to Set the System Mode to ON. Refer to∙ Each time the DTV button is pressed, the operating mode Will switch between DTV and TV mode. To change the inputMenu Index SET UP menu SeeMain menu See Closed Caption menu SeeChange Password menu See Channel SET UP menu SeeAuto Channel Preset menu See Convergence menu See pages 30Symptom CAUSE/REMEDY Pages TroubleshootingSymptom Cause Specifications Others 99I00SF0W00 0 4 2 1 1 4 0
Related manuals
Manual 83 pages 976 b

PRO 510HD, PRO-610HD specifications

The Pioneer PRO-510HD and PRO-610HD are two advanced professional display monitors that exemplify cutting-edge technology in the realm of high-definition visual solutions. Designed for various applications, including broadcasting, live events, and video production, these monitors provide exceptional image quality and versatile features.

One of the standout characteristics of both models is their high-resolution display capabilities. The PRO-510HD boasts a 51-inch screen size with an impressive resolution of 1920 x 1080 pixels, ensuring sharp and vibrant images that meet the demands of professional users. The larger PRO-610HD features a 61-inch screen size with the same high-definition resolution, allowing for an immersive viewing experience.

These monitors leverage advanced LCD technology to deliver remarkable color accuracy and consistent brightness. With a wide color gamut, users can expect true-to-life colors, making these monitors ideal for color-critical applications. The brightness levels of both models reach up to 700 cd/m², ensuring visibility even in brightly lit environments.

Connectivity is a crucial aspect of any professional monitor, and the PRO-510HD and PRO-610HD are equipped with a range of input options. They offer multiple HD-SDI, HDMI, DVI, and analog connections, allowing for seamless integration with various broadcasting and production equipment. This flexibility ensures that users can easily connect their devices without the need for additional converters or adapters.

Another significant feature of these monitors is the built-in waveform and vector scope displays. These tools are essential for ensuring proper exposure and color balance, providing users with real-time monitoring of their video signals. The monitors also support various aspect ratios, making it easy to adjust the display according to specific project requirements.

Durability is key for professional equipment, and both the PRO-510HD and PRO-610HD are constructed with robust materials, ensuring longevity even in demanding environments. The monitors are designed for continuous operation, making them reliable for long hours of use whether in studios or on location.

In conclusion, the Pioneer PRO-510HD and PRO-610HD are powerful tools for professionals who require high-quality displays with advanced features. Their excellent image quality, extensive connectivity options, and integrated monitoring tools make them an attractive choice for anyone involved in video production or broadcasting. With their durable design and user-friendly operation, these monitors stand out as reliable partners in the visual media landscape.
Top Page Image Contents