Pioneer DVR-231-AV, DVR-231-S, DVR-233-S manual Audio Out

Page 51

The Initial Setup menu

08

From the Audio Adjust screen, use the buttons to adjust the Audio DRC setting On or Off. (Off leaves the dynamic range untouched; On ‘squashes’ the dynamic range, making it good for lower-level listening.)

Audio Adjust

Audio DRC

Off

 

 

Press ENTER to confirm and exit the screen.

Audio In

Audio

Basic

Audio Adjust

External Audio

Disc

Audio In

Dual Mono

Video

Audio Out

Input Level

Audio

 

 

Recording

 

 

Playback

 

 

 

 

 

Use the Audio In settings to specify which channel(s) of a dual mono source to record and adjust the analog audio input level.

From the Audio In screen, use the

buttons to select

a setting, then use the

buttons to adjust it.

Audio In

 

 

External Audio

Stereo

 

Dual Mono Rec

L

 

Input Level

0dB

 

•External Audio – Select Stereo if the external audio input is regular stereo, or Dual Mono if each channel carries a separate soundtrack.

•Dual Mono Rec – When recording a dual mono source from an external input in Video mode or VR mode set to XP, you can choose to record the L (left), or the R (right) audio channel.

•Input Level – Use to attenuate the analog audio input level. (External input only)

Note

•Except in XP recording mode, if you’re recording in VR mode, both channels will be recorded and you can switch them as you like on playback.

Audio Out

Audio

Basic

Audio Adjust

Dolby Digital

Disc

Audio In

96kHz PCM

Video

Audio Out

DTS

Audio

 

MPEG

Recording

 

 

Playback

 

 

 

 

 

 

 

 

Use the various Audio Out settings to make sure that the digital audio output is compatible with your AV receiver (or other connected component). You may need to check the operating instructions that came with your AV receiver to see which digital formats it’s compatible with.

From the Audio Out screen, use the

buttons to

select a setting, then use the

buttons to adjust it.

Audio Out

 

 

Dolby Digital

Dolby Digital

 

96kHz PCM

96kHz -> 48kHz

 

DTS

On

 

MPEG

MPEG -> PCM

 

•Dolby Digital – If your AV receiver, etc. is Dolby Digital compatible, set to Dolby Digital, otherwise set to Dolby Digital -> PCM.

•96 kHz PCM – If your AV receiver, etc. is compatible with high sampling rate audio (88.2 / 96 kHz), set to 96kHz, otherwise set to 96kHz -> 48kHz.

•DTS – If your AV receiver, etc. has a built-in DTS decoder, set to On, otherwise set to Off. (See also Important below.)

•MPEG – If your AV receiver, etc. is MPEG audio compatible, set to MPEG, otherwise set to MPEG -> PCM.

Important

•If you set DTS to On with a non-DTS compatible amplifier, noise will be output when you play a DTS disc.

•When set to On, there is no analog audio output when playing a DTS DVD-Video disc.

•When playing a DTS audio CD (even when DTS is Off), noise is output from the analog outputs. Do not play this through your amplifier and speakers.

•When playing a DTS audio CD, make sure that Stereo is selected using the AUDIO button. See Switching DVD soundtracks on page 31.

English

51

En

Page 50 Page 52
Image 51
Page 50 Page 52
Contents DVR-231-SDVR-231-AVDVR-233-S Risk of Electric Shock Do not Open Information to UserImportant Safety Instructions POWER-CORD Caution To establish a safe level Once you have established a comfortable sound levelDecibel Level Example Contents What’s in the box FeaturesBefore you start Before you start ChapterDVD-Video Using the remote controlDisc / content format playback compatibility General disc compatibilityCD-R/RW compatibility Frequently asked questionsBefore you start DVD-R/RW compatibilityFront panel connections Connecting upConnecting up Chapter Rear panel connectionsVCR Connecting up Easy connectionsConnecting up Using other types of video output Connecting using an S-video outputConnecting using the component video output Connect RF antenna cables as shown This enables you to watch discs Video OUT Digital COAXIAL1 Connecting up Connecting to an AV amplifier or receiverConnecting up Connecting other AV sources Connecting a VCR or analog camcorderPlugging Display Controls and displaysControls and displays Chapter Front panelControls and displays Remote controlTimer REC Switching on and setting up Getting startedGetting started Chapter Your time zone Other settings you can makeGetting started UseChanging TV channels Using the built-in TV tunerGetting started Making your first recording Playing back your recordingChanging audio channels Basic playbackPlaying DVD discs Playing audio CDsPlaying Video CDs Stop display Displaying disc information on- screenRecording display Play displayIntroduction Using the Disc Navigator to browse the contents of a discPlayback Playback ChapterOptionally Press Enter PlaybackNavigating discs Scanning discsFrame advance/frame reverse Playing in slow motionSlow 1/16 Slow 1/8 Slow 1/2 Enter to navigate Playback Play Mode menuSearch Mode Press Home Menu and select ‘Play Mode’Repeat play Displaying and switching subtitlesSwitching DVD soundtracks Repeat play modeTo switch the camera angle, press Angle Switching audio channelsSwitching camera angles To display/switch the audio channel, press Audio repeatedlyRecording time and picture quality RecordingRecording Chapter About DVD recordingRecording equipment and copyright Setting the picture quality/recording timePress REC Mode repeatedly to select a recording setting Recording Restrictions on video recordingRecording Basic recording from the TV Setting a timer recordingRecording Enter the timer recording settingsButtons to change Timer recording using the VCR Plus+ programming systemExtending a timer recording in progress Moving the end time by 30-minute blocksTimer recording FAQ Canceling and stopping a timer recording in progressProgramming a new end time Press Recording from an external componentPlaying your recordings on other DVD players Finalizing a discInitializing a DVD-RW disc Erase EditingEditing Chapter Editing Titles Title EditPlayback point Currently selected chapter number EditingTitle Name Navigation Mark Navi MarkTo lock or unlock, then press Enter Editing chapters Chapter EditLock Erase AllCombine DivideBasic settings Initial Setup menuInitial Setup menu Chapter Using the Initial Setup menuThen press Enter Initial Setup menuAuto CH Setup TunerManual CH Setup Guide CH SetupOSD Language Remote Control Setup NavigatorDisplay Video settings Initial Setup menu Disc settingsAudio Adjust setting Audio settingsInput Adjust Playback AdjustAudio Out AudioPlayback settings Initial Setup menu Recording settingsSelect ‘Level’ Set PasswordChange Password Change LevelLanguage Country/AreaSelect by code letter Use Buttons to Change the code Visual settings Action settingsSelecting ‘Other’ languages Additional information Chapter When viewing on a standard TV or monitorWhen viewing on a widescreen TV or monitor Additional informationAdditional information Troubleshooting Problem RemedyGeneral Additional information What kind of discs can I use for recording? Additional information Frequently asked questionsAdditional information Language code list Country/Area code listCountry/Area, Country/Area code, Country/Area code letter Message Explanation/Action Storing discs Cleaning the pickup lensHints on installation Additional information Handling discsMoving the recorder Resetting the recorderMaking a timer recording Setting upMpeg video Dolby DigitalDynamic range Mpeg audioInput/Output Additional information SpecificationsTimer Supplied accessoriesIndex Language audio 31, 54 code list 60 DVD menuEnglish Pioneer Corporation
Top Page Image Contents