Chapter 5: Commercial Interface Menus
These TVs include a full commercial interface that allows your facility to customize the performence to your specific needs. These settings are only accessible to the installer with the use of the Master Remote(R130K2). Contact your RCA Commercial Distribution to obtain a master remote.
You can access this menu by pressing MENU
Commercial Interface
|
|
|
|
|
|
|
| Commercial Interface | On | F G |
|
|
| Clone Management |
| G | |
|
| Channel |
| G | |
|
| OSD |
| G | |
|
| Source |
| G | |
|
| Volume |
| G | |
|
| Power Management |
| G | |
|
| Key Management |
| G | |
|
| Reset Commercial Interface |
| G | |
|
|
| Select | MENU Exit | |
|
|
|
|
|
|
- You must set “Commercial Interface” to “On” to activate the below items.
Channel
Commercial Interface
|
| Commercial Interface | On | F G | |
|
| ||||
|
| Clone Management |
| G | |
|
| Channel |
| G |
|
|
| OSD |
| G | |
|
| Source |
| G | |
|
| Volume |
| G | |
|
| Power Management |
| G | |
|
| Key Management |
| G | |
|
| Reset Commercial Interface |
| G | |
|
| ENTER OK | Select | MENU Exit | |
|
|
|
|
|
|
Commercial Interface
|
|
|
|
|
|
|
|
|
| Direct Tuning Access |
| On |
| F G |
|
|
| ATSC Tune Mode |
| Virtual |
| F G | |
|
| Power On Source |
| Off |
| F G | |
|
| Power On Major Channel |
|
|
| 2 |
|
|
| Power On Miner Channel |
|
|
| 0 |
|
|
| Channel Hold |
| Off |
| F G | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Select | MENU Back | ||
-Direct Tuning Access : If this function is on, you can tune to channels even if the channels are not in the channel list using the numeric keys. If this function is off, only channels in the channel list can be tuned.
-ATSC Tune Mode : This function sets the channel frequency type for Digital Channels to physical or virtual. If the facility has a head end signal distribution system, set this to “physical”.
-Power On Source : Use this setting to configure the signal source of the TV when it is turned on.
-Power On Major/Minor Channel : Use this setting to configure the initial channel of the TV when it is turned on.
Note: “Power On Source” should be set to “TV” to use this setting. To tune to an analog channel, set minor channel to 0.
-Channel Hold : If this function is on then you cannot change channels.
OSD
Commercial Interface
|
| Commercial Interface | On | F G | |
|
| ||||
|
| Clone Management |
| G | |
|
| Channel |
| G | |
|
| OSD |
| G |
|
|
| Source |
| G | |
|
| Volume |
| G | |
|
| Power Management |
| G | |
|
| Key Management |
| G | |
|
| Reset Commercial Interface |
| G | |
|
| ENTER OK | Select | MENU Exit | |
|
|
|
|
|
|
Commercial Interface
|
|
|
|
|
|
|
| Channel Banner | On | F G |
|
|
| OSD Timer | 60S | F G | |
|
| Clear |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Select | MENU Back | |
-Channel Banner : If this function is off then channel banner will not appear when channel is changed.
-OSD Timer : Use this setting to configure the menu OSD time out.
-Clear
Chapter 5 | 19 |