Panasonic PT-56LCZ70, PT-61LCZ70-K, PT-50LCZ70-K manual First Time Setup, Language, Auto program

Page 25

First Time Setup

For your convenience, First Time Setup menu will be displayed on screen when the set is turned on for the first time. If needed, follow the menus and procedures displayed on-screen for setting up the features.

Language

The language of the on-screen display is set to English as the factory setting. You can select English, Spanish or French as the on-screen display language.

Procedure

1.Press ▲▼ to select “Language”.

2.Press OK to display the Language menu.

First time setup

Language

Auto program

Picture

3.Press ◄► to select “English,” “Español” or “Français”.

4.Press RETURN to go to previous screen.

Language

Language English

Auto program

You can scan All (Analog and Digital) channels. If needed, follow the menus and procedures displayed on-screen for setting up the features. You can also make the settings in Setup menu.

Procedure

1.Press ▲▼ to select “Auto program”.

2.Press OK to display the Program channel menu.

First time setup

Language

Auto program

Picture

3.Press ▲▼ to select “ANT in”.

4.Press ◄► to select “Cable” or “Antenna”.

Program channel

ANT in

 

Cable

Auto

 

5.Press ▲▼ to select “Auto”.

6.Press OK to display the Auto program menu.

Program channel

ANT in

 

Cable

Auto

 

7.Press ▲▼ to select “All channels”, “Analog only”, or “Digital only”.

8.Press OK to start scan.

• Channels available for reception will be set automatically.

Auto program

All channels

Analog only

Digital only

Auto program

Scanning digital channel

Progress

Quit40%

9.After Auto program is complete, the unit will return to Manual program mode. To place the channels that were located by auto scan in memory, move the cursor to “Apply” and press OK. (p. 27-28)

If OK is not pressed after selecting APPLY, the channels will not be memorized.

10.Press ▲▼ to select “Picture”.

11.Press OK to display the Picture menu. (p. 35)

First time setup

Language

Auto program

Picture

Notes

•After “Auto program” is completed the unit tunes to the first channel found during “Auto program”.

•If setup is incomplete, check connection of Antenna/Cable to the RF IN Terminal, then try “Auto program” again. (p. 26-27)

•“Auto program” must be done when you select the input signal for the first time or whenever you change the antenna configuration.

•Depending on conditions, “Auto program” may take a while.

Basic Operation

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Puerto Rico Product safety notificationCanada Case your new Projection Display is stolenFollow all instructions carefully Keep these instructions for future referenceViVA Getting StartedFor assistance, please call For assistance, please call 1-888-VIEW PTV843-9788FCC Caution For U.S.ATable of Contents Before Using Reset All Memory Functions Remote Control Battery InstallationObserve the following precautions Install batteries in the battery compartmentProjection Display CleaningLocation of Controls Remote ControlFront View Model PT-56LCZ70 unit shown Controls and Terminals on the Projection DisplayRear View Model PT-56LCZ70 unit shown Connected Equipment Introduction Signal source InstallationReference of connection To connect antenna terminals Example 1 Connecting Antenna To watch TVExample 2 Connecting DVD recorder VCR To record/playback To use Component terminals To use Hdmi terminalsTo use Composite terminals To use S Video terminalsConnecting this Projection Display and DVD recorder VCR Example 3 Connecting DVD recorder VCR and satellite receiverSatellite receiver To connect Hdmi terminals Example 4 Connecting Home Theater and DVD recorderTo connect PC terminals Connecting PCPC in Terminal D-SUB 15P Pin Layouts NC Not connectedRGB signals that can be input Images Recommended AV ConnectionsDVD Player/Set Top Box Amplifier Camcorder/VCR/DVD PlayerEZ Sync Connections Setting this unit after connectionsHdmi connection Input signals that can be displayedAbout Hdmi Turning the Power on and OFF Power on / OFFPower on Power OFFLanguage First Time SetupAuto program Press to select ANT Press to select Cable or AntennaSwitching languages for display Tuning channelsAutomatic program setting Press to select English, Español or FrançaisPress to select ANT Press to select Antenna or Cable Manual program settingPress to select the desired preset channel line Press to select Edit Press OK to enter the edit modeEdit Caption Press to select Apply Press OK to enter the CaptionRapid Tuning Selecting Input ModeUsing the CH/VOL Button Projection Display OperationUnit Status Display Channel and Program TuningAudio Mute Set Favorite Feature Favorite FeaturePress SUB Menu to display the Setup SUB Menu Display the SUB MenuUse Favorite Feature Select Audio Mode for TV ViewingDigital mode Analog modeAspect mode changes each time Aspect is pressed Changing the Aspect ModeAspect Controls EZ Sync EZ Sync FeaturePress to select the equipment Return to TV screenPress to select each item Press to adjust each item Picture AdjustmentsPro Setting Picture ModeZoom Adjust Press to select Picture mode Press to select picture modeOther Adjust PC AdjustNormal / Bass / Treble / Balance Audio AdjustmentsBBE Viva Set Sleep Timer Sleep Timer FeaturePress to select 0, 30, 60, or Enter Password Lock FeatureCreate Password Press Number keys to enter your passwordPress to select Mode Press to select the desired setting Enter PasswordPress to select Mode Press to select Custom Lock SetMonitor out setting Rating level settingGame Lock Block programMovies Ratings Chart Mpaa Blocking Messages Change passwordInsert/Remove the Card Viewing from SD CardCard Warning Messages Insert the CardSingle Play Mode Photo viewer ModeSlide Show Mode Exit Photo viewerTo Watch Photos in Slide Show Mode Single Play ModeTo Adjust Picture Viewing from a GalleryPlayer SD CardSurf Mode Setup FeaturesSignal Meter Press to select Surf mode Press to select Favorite or AllMonitor out Input labelsPress to select desired channel Press to select each item Press to select the input labelCC Mode for Analog CC ModeCC Mode for Digital CC Closed CaptionCC Reset Digital settingsPress to select each item Press to select the setting EZ Sync Hdavi ControlSpeaker control Automatic Input SwitchingPress to select EZ Sync Press to select On Press EZ Sync to display the EZ Sync menuOne-touch theater playback Available this Projection Display’s remote control buttonsHome theater Press to select each item Press to select Set or NoAbout ResetPress to select About Press OK to display the About screen Confirmation screen is displayed. Select Yes, and press OKOperating Peripheral Equipment To find a code not listed in the code ListRemote Control Operation List Remote Control Operation/Code ListRemote Control Code List Remote Control Operation/Code ListVCR DBS/PVR Combination Power OFF TroubleshootingChannel Capability SpecificationsNpcparts@us.panasonic.com Customer Services Directory for U.S.ALimited Warranty Coverage Limited Warranty for U.S.ACarry-in or In-Home Service Limited Warranty Limits And ExclusionsLCD Rear Projection TV In home Service Parts Labour Limited Warranty for CanadaPanasonic Canada Inc DTV IndexCustomer’s Record
Top Page Image Contents