Network settings, Setting the IP address

Network settings

These settings are used if you will connect this unit to the Internet. ≥The connection to the Internet may take time or the Internet may not be

connected depending on the connection environment. (> 35) It is required that you use a broadband connection.

Preparation

≥Connect to a broadband network. (> 16)

Testing of “IP Address/DNS Settings”

Always test the connection when a LAN cable is connected.

1 Press [SETUP].
2 Press [3, 4] to select “Network”
and press [OK].
3 Press [3, 4] to select “IP Address/
DNS Settings” and press [OK].
4 Press [3, 4] to select “Connection
Test” and press [OK].
IP Address/DNS Settings
Connection Test
IP Address Auto Configuration (DHCP)	On
IP Address	㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㩷
Subnet Mask	㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㩷
Default Gateway	㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㩷
DNS Auto Configuration (DHCP)	On
Primary DNS	㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㩷
Secondary DNS	㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㪅㩷㪄㪄㪄㩷
Auto Detect Connection Speed	On
Connection Speed Setting
OK
RETURN

“Testing”:	The test is in progress.
“Pass”:	The connection is completed.
	Press [RETURN] to exit.
“Fail”:	Please check the connection and settings. (> 40)

≥Perform the “Connection Test” also when any change was made to the “IP Address/DNS Settings”.

≥If the connection test fails, it may be necessary to set the MAC address of this unit at the router side. The MAC address can be displayed by pressing [SETUP] and selecting “Network”.

Network

IP Address/DNS Settings

Proxy Server Settings

Network Service

MAC Address: xx-xx-xx-xx-xx-xx

RETURN

Setting the IP address

In most cases, default settings can normally be used without
making any changes.	started
Set the IP address only when the router has no DHCP server	started
functions or when the router’s DHCP server function is disabled.
After performing steps 1–3 (D left)	Getting
4 Press [3, 4] to select “IP Address	Getting
Auto Configuration (DHCP)” and

press [2, 1] to select “Off”.

5Press [3, 4] to select “IP Address”, “Subnet Mask” or “Default

Gateway” and press [OK].

6Enter numbers with the numbered buttons and press [OK].

7Press [2, 1] to select “Yes” and press [OK].

≥After checking the specifications for your broadband router, enter each number. If the number is unknown, then check the number of other devices such as personal computers connected via a LAN cable. Assign a different number from those of other devices for the “IP Address” and the same number for others.

≥If a wrong number is entered, then press [CANCEL].

≥The numeric input range is between 0 and 255.

Setting the DNS-IP

In most cases, default settings can normally be used without making any changes.

When setting an assigned DNS server from your Internet service provider, perform the following settings.

After performing steps 1–3 (D left)

4Press [3, 4] to select “DNS Auto

Configuration (DHCP)” and press [2, 1] to select “Off”.

5Press [3, 4] to select “Primary DNS” or “Secondary DNS”and press [OK].

6Enter numbers with the numbered buttons and press [OK].

Primary DNS

Please input Primary DNS and press

[OK]. Press [CANCEL] to delete the selected character. To clear this setting, delete all characters and press [OK].

192

0 - 9

Number

7Press [2, 1] to select “Yes” and press [OK].

≥Follow the instructions given by your Internet service provider and enter the numbers. If the number is unknown, then check the number of other devices such as personal computers connected via a LAN cable and assign the same number.

≥If a wrong number is entered, then press [CANCEL]. ≥The numeric input range is between 0 and 255.

RQT9378