Panasonic TH-50PF11UK, TH-65PF11UK, TH-58PF11UK manual PC Input Terminals connection, Connections

Page 10

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

(Female)

AUDIO

PC IN

Mini D-sub 15p

RGB

PC cable

(Male)

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

•Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal.

•With regard to the typical PC input signals that are described in the applicable input signals list (see page 51), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list.

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

•The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

•Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

•Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 39)

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10

9

 

8

7

6

15

14

 

13

12

 

11

Pin Layout for PC Input Terminal

Pin No.

Signal Name

Pin No.

Signal Name

Pin No.

Signal Name

1

R (PR/CR)

6

GND (Ground)

11

NC (not connected)

2

G (Y)

7

GND (Ground)

12

SDA

3

B (PB/CB)

8

GND (Ground)

13

HD/SYNC

4

NC (not connected)

9

+5 V DC

14

VD

5

GND (Ground)

10

GND (Ground)

15

SCL

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents English Español Operating Instructions Manual de instruccionesModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits Safety Precautions When using the Plasma DisplaySetup MaintenanceSafety Precautions / Maintenance AC Power Supply CordAccessories Supplied AccessoriesRemote Control Batteries Cable fixing band ConnectionsAC cord fixing Secure any excess cables with band as requiredPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorConnections Serial Terminals connection Signal names for D-sub 9P connectorCommand Communication parametersRCA-BNC Hdmi connectionComponent / RGB connection DVDConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet Present Time Setup Power on / OFFWhen first switching on the unit OSD LanguageSelecting the On-Screen Menu Language Selecting the input signalInitial selections INPUT1 INPUT2A INPUT2B INPUT3 PCBasic Controls Remote control sensor Volume AdjustmentMain Power On / Off Switch Power Indicator Menu Screen on / OFFBasic Controls On OFFAspect Controls All Aspect modePanasonic Auto During PIP Selecting the Display ModeAspect Controls During Advanced PIPTransparent Function and Insertion Function Swapping ScreensDuring Blend PIP Composite Screen Function Transparent Function Insertion FunctionSelecting the Sub Screen Position During P in P Display Selecting the Target Screen for OperationsOperations on Main screen Sub screen Select the area of the image to be enlarged Digital ZoomDisplay the operation guide Select the magnification required for the enlarged displayOn-Screen Menu Display Adjusting POS. /SIZE 2k1k Adjusting POS. /SIZEAdjusted as follows For 2k1k signals OFF On Left On Center On RightDynamic Picture AdjustmentsStandard CinemaAdvanced Settings Picture AdjustmentsSound Adjustment SDI Sound OutputPresent Time Setup SET UP TimerStart setting Setup of Screensaver TimeMode selection Screensaver For preventing image retentionScreensaver For preventing image retention Side BAR AdjustReduces screen image retention OFF Dark MID BrightReduces power consumption Addition sign Selected Input Customizing the Input labelsLandscape Portrait Display Number locations for each arrangement Examples SET UP for Multi DisplayHow to setup Multi Display × 1 2 ×ID remote control button operation ID Remote Control FunctionSET UP for Multi Display ID CancellationPIP Advanced PIP Blend PIP Transparent Display of the Sub Screen During Blend PIPSub Screen Insertion During Blend PIP Insert LevelHow to setup Portrait SET UP for PortraitPress to select the Portrait Setup Viewing Area Location SET UP for PortraitPress twice to exit from SET UP Undisplayed area 48 dotsComponent / RGB in Select SET UP for Input SignalsYUV / RGB in Select SET UP for Input Signals Signal menu3D Y/C Filter For Ntsc AV images Pulldown XGA ModeColor System / Panasonic Auto Color SystemNoise Reduction Press to adjustRefresh Rate Advanced NRSync Input signal displaySetting RGB sync signal SDI ThroughOptions Adjustments Options1/3Options Adjustments INPUT1 INPUT2 INPUT3Delay NormalizationProgram number Weekly Command TimerPress Action button Program Edit screenShipping condition Troubleshooting Plasma Display panelList of Aspect Modes FullApplicable Input Signals MHz Active pixels Pixels Active lines Lines Applicable Input SignalsVideo input Hdmi VGA60Command list of Weekly Command Timer Specifications TH-42PF11UK TH-50PF11UKSpecifications TH-58PF11UK TH-65PF11UKPanasonic Professional Flat Panel Display Limited Warranty For the U.S.A and Puerto RicoLimited Warranty Statement For CanadaPage Executive Office Customer’s RecordPanasonic Professional Display Company Panasonic Canada Inc
Related manuals
Manual 60 pages 19.82 Kb
Top Page Image Contents