Panasonic TH-58PF11UK, TH-65PF11UK, TH-50PF11UK Connections, AC cord ﬁxing, Cable ﬁxing band, See

Page 9

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

Speaker terminal (R)

Speaker terminal (L)

AC cord connection (see page 13)

– AC cord ﬁxing

1
2	1
	1
	2

11 Plug the AC cord into the display unit.

Plug the AC cord until it clicks.

2Fix the AC cord with the clamper

2	which is attached to the unit.
Note:	For TH-42PF11UK, TH-58PF11UK:
Note:	Clampers are not installed to this
Make sure that the AC	unit. Ensure there is sufﬁcient slack
cord is locked on both	in the AC cord and ﬁrmly bind with
the left and right sides.	the supplied cable ﬁxing band, etc.

–Cable ﬁxing band

Secure any excess cables with band as required.

Note:

Close

Push until the hook clicks.

Open

2. Pull off.

1.Keep the knob pressed.

Unplug the AC cord

Unplug the AC cord pressing the two knobs.

Note:

When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ﬁrst.

One ﬁxing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately.

Pass the attached cable ﬁxing band through the clip as shown in the ﬁgure.

To secure cables connected to Terminals, wrap the cable ﬁxing band around them then pass the pointed end through the locking block, as shown in the ﬁgure.

While ensuring there is sufﬁcient slack in cables to minimize stress (especially in the power cord), ﬁrmly bind all cables with the supplied ﬁxing band.

To tighten:	To loosen:
	Push the catch

	Pull
1	2					Pull
	R AUDIO	L	PR/CR/R PB/CB/B	Y/G		AUDIO
						AUDIO
	COMPONENT/RGB IN
SLOT1	SLOT2		SLOT3	PC	IN	SERIAL

Optional Terminal Board Insert Slot (covered)

Dual HDMI Terminals (equivalent of Dual HDMITerminal Board (TY-FB10HMD))

(see page 12)

COMPONENT/RGB IN and Audio IN Terminals (equivalent of BNC Component Video Terminal Board (TY-42TM6A)) (see page 12)

From EXTERNAL monitor terminal on Computer (see page 10)

From SERIAL Terminal on Computer (see page 11)

Note: At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.

9

Image 9

Contents Operating Instructions Manual de instrucciones English EspañolModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents FCC Caution Canadian NoticeTrademark Credits When using the Plasma Display Safety PrecautionsSafety Precautions / Maintenance MaintenanceSetup AC Power Supply CordAccessories Accessories SuppliedRemote Control Batteries AC cord ﬁxing ConnectionsCable ﬁxing band Secure any excess cables with band as requiredSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionConnections Command Signal names for D-sub 9P connectorSerial Terminals connection Communication parametersComponent / RGB connection Hdmi connectionRCA-BNC DVDPower on / OFF Connecting the AC cord plug to the Plasma DisplayConnecting the plug to the Wall Outlet When ﬁrst switching on the unit Power on / OFFPresent Time Setup OSD LanguageInitial selections Selecting the input signalSelecting the On-Screen Menu Language INPUT1 INPUT2A INPUT2B INPUT3 PCMain Power On / Off Switch Power Indicator Remote control sensor Volume AdjustmentBasic Controls Menu Screen on / OFFOn OFF Basic ControlsAll Aspect mode Aspect ControlsPanasonic Auto Aspect Controls Selecting the Display ModeDuring PIP During Advanced PIPDuring Blend PIP Composite Screen Function Swapping ScreensTransparent Function and Insertion Function Transparent Function Insertion FunctionSelecting the Target Screen for Operations Selecting the Sub Screen Position During P in P DisplayOperations on Main screen Sub screen Display the operation guide Digital ZoomSelect the area of the image to be enlarged Select the magniﬁcation required for the enlarged displayOn-Screen Menu Display Adjusting POS. /SIZE Adjusted as follows For 2k1k signals Adjusting POS. /SIZE2k1k OFF On Left On Center On RightStandard Picture AdjustmentsDynamic CinemaPicture Adjustments Advanced SettingsSDI Sound Output Sound AdjustmentSET UP Timer Present Time SetupMode selection Setup of Screensaver TimeStart setting Screensaver For preventing image retentionReduces screen image retention Side BAR AdjustScreensaver For preventing image retention OFF Dark MID BrightReduces power consumption Customizing the Input labels Addition sign Selected InputLandscape Portrait How to setup Multi Display SET UP for Multi DisplayDisplay Number locations for each arrangement Examples × 1 2 ×SET UP for Multi Display ID Remote Control FunctionID remote control button operation ID CancellationSub Screen Insertion During Blend PIP Transparent Display of the Sub Screen During Blend PIPPIP Advanced PIP Blend PIP Insert LevelSET UP for Portrait How to setup PortraitPress to select the Portrait Setup Press twice to exit from SET UP SET UP for PortraitViewing Area Location Undisplayed area 48 dotsSET UP for Input Signals Component / RGB in SelectYUV / RGB in Select Signal menu SET UP for Input Signals3D Y/C Filter For Ntsc AV images Color System / Panasonic Auto XGA ModePulldown Color SystemRefresh Rate Press to adjustNoise Reduction Advanced NRSetting RGB sync signal Input signal displaySync SDI ThroughOptions1/3 Options AdjustmentsINPUT1 INPUT2 INPUT3 Options AdjustmentsNormalization DelayPress Action button Weekly Command TimerProgram number Program Edit screenShipping condition Plasma Display panel TroubleshootingFull List of Aspect ModesApplicable Input Signals Video input Hdmi Applicable Input SignalsMHz Active pixels Pixels Active lines Lines VGA60Command list of Weekly Command Timer TH-42PF11UK TH-50PF11UK SpeciﬁcationsTH-58PF11UK TH-65PF11UK SpeciﬁcationsFor the U.S.A and Puerto Rico Panasonic Professional Flat Panel Display Limited WarrantyFor Canada Limited Warranty StatementPage Panasonic Professional Display Company Customer’s RecordExecutive Ofﬁce Panasonic Canada Inc

Related manuals

Manual 60 pages 19.82 Kb