Panasonic TH-50PF11UK, TH-65PF11UK, TH-58PF11UK, TH-42PF11UK manual Normalization, Delay

Page 46

Options Adjustments

Item

 

 

 

 

Adjustments

 

 

 

Off:

Nullify all the settings adjusted.

 

 

Studio W/B

On:

Sets the color temperature for TV studio.

 

 

 

Note: Valid only when the “WARM” is set as “COLOR TEMP” in PICTURE menu.

 

 

Sharpens the contrast for a better view when a part of the image is too light to see.

 

 

Off:

Disables “Studio Gain”.

 

 

Studio Gain

On:

Enables “Studio Gain”.

 

 

 

Note: This setting is valid only when the input signals are as follows:

 

 

 

Component Video, RGB (analog), SDI, HDMI

 

 

 

Off

 

Auto

On

 

 

 

 

Off:

Power is not transmitted to the slot power.

 

 

Slot Power

Auto: Power is transmitted to the slot power only when main power is on.

 

On:

Power is transmitted to the slot power when main power is on or in the standby state.

 

 

 

 

Note: In some cases, power is transmitted to the slot power when main power is on or in the standby state

 

 

regardless of the slot power setting.

 

 

 

Off

1

2

3....

30

 

 

 

You can set the power-on delay time of the displays to reduce the power load, when you press

to turn

 

on the multiple displays that are set together, for example, on MULTI DISPLAY system.

 

 

Set each display’s setting individually.

 

 

 

Off:

 

The display will be turned on at the same time as

is pressed.

 

 

1 to 30 (sec.): Set the power-on delay time (second).

 

 

Power On Screen

Notes:

 

After pressing

, the display will be powered on with time delay depending on this setting.

Delay

 

 

 

 

 

 

•During this function is working, the power indicator is blinking green.

•This function also works when the power recovers from failure or after plugging off and in again the power cord. After you unplug and plug the power cord in while the unit is in standby mode and also the power is being supplied to a terminal board, the unit will start supplying the power to the board with time delay according to the setting.

The power indicator lights up red first and it turns orange when the power starts being supplied to the board.

Off: Not display the clock.

On: Display the clock.

The clock is displayed at the lower left of the screen when button is pressed.

Clock Display

10:00

Note: When “PRESENT TIME SETUP” is not set, the clock is not displayed even if “Clock Display” is “On” (see page 29)

 

Sets All Aspect mode (advanced aspect setting) or default aspect mode.

 

With each press of

button, the aspect changes in the selected mode.

 

Off:

Default aspect mode

All Aspect

On:

All Aspect mode

 

Aspect mode of each setting is as follows:

 

 

(Example: HD signal)

 

 

Off

4:3→H-FILL→ZOOM→FULL→JUST

 

On

4:3 (1)→4:3 (2)→4:3 Full→Zoom1→Zoom2→Zoom3→16:9→14:9→Just1→Just2

Rotate

Off:

Does not rotate the image.

On:

Rotates the image 180 degrees.

 

Serial Slot

Slot1

Slot2

Slot3

Selects the slot which communicates serial.

Select

Note: The setting of an external command can be set only from the fixed serial terminal. (see page 11)

 

Normalization

When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote ID” adjustments, set all the values “Off” so that all the buttons are enabled again.

Press the

button on main unit together with

button on the remote control and hold for more than 5 seconds. The

“SHIPPING” menu is displayed and the lock is released when it disappears.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents English Español Operating Instructions Manual de instruccionesModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits Safety Precautions When using the Plasma DisplaySetup MaintenanceSafety Precautions / Maintenance AC Power Supply CordAccessories Supplied AccessoriesRemote Control Batteries Cable fixing band ConnectionsAC cord fixing Secure any excess cables with band as requiredPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorConnections Serial Terminals connection Signal names for D-sub 9P connectorCommand Communication parametersRCA-BNC Hdmi connectionComponent / RGB connection DVDConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet Present Time Setup Power on / OFFWhen first switching on the unit OSD LanguageSelecting the On-Screen Menu Language Selecting the input signalInitial selections INPUT1 INPUT2A INPUT2B INPUT3 PCBasic Controls Remote control sensor Volume AdjustmentMain Power On / Off Switch Power Indicator Menu Screen on / OFFBasic Controls On OFFAspect Controls All Aspect modePanasonic Auto During PIP Selecting the Display ModeAspect Controls During Advanced PIPTransparent Function and Insertion Function Swapping ScreensDuring Blend PIP Composite Screen Function Transparent Function Insertion FunctionSelecting the Sub Screen Position During P in P Display Selecting the Target Screen for OperationsOperations on Main screen Sub screen Select the area of the image to be enlarged Digital ZoomDisplay the operation guide Select the magnification required for the enlarged displayOn-Screen Menu Display Adjusting POS. /SIZE 2k1k Adjusting POS. /SIZEAdjusted as follows For 2k1k signals OFF On Left On Center On RightDynamic Picture AdjustmentsStandard CinemaAdvanced Settings Picture AdjustmentsSound Adjustment SDI Sound OutputPresent Time Setup SET UP TimerStart setting Setup of Screensaver TimeMode selection Screensaver For preventing image retentionScreensaver For preventing image retention Side BAR AdjustReduces screen image retention OFF Dark MID BrightReduces power consumption Addition sign Selected Input Customizing the Input labelsLandscape Portrait Display Number locations for each arrangement Examples SET UP for Multi DisplayHow to setup Multi Display × 1 2 ×ID remote control button operation ID Remote Control FunctionSET UP for Multi Display ID CancellationPIP Advanced PIP Blend PIP Transparent Display of the Sub Screen During Blend PIPSub Screen Insertion During Blend PIP Insert LevelHow to setup Portrait SET UP for PortraitPress to select the Portrait Setup Viewing Area Location SET UP for PortraitPress twice to exit from SET UP Undisplayed area 48 dotsComponent / RGB in Select SET UP for Input SignalsYUV / RGB in Select SET UP for Input Signals Signal menu3D Y/C Filter For Ntsc AV images Pulldown XGA ModeColor System / Panasonic Auto Color SystemNoise Reduction Press to adjustRefresh Rate Advanced NRSync Input signal displaySetting RGB sync signal SDI ThroughOptions Adjustments Options1/3Options Adjustments INPUT1 INPUT2 INPUT3Delay NormalizationProgram number Weekly Command TimerPress Action button Program Edit screenShipping condition Troubleshooting Plasma Display panelList of Aspect Modes FullApplicable Input Signals MHz Active pixels Pixels Active lines Lines Applicable Input SignalsVideo input Hdmi VGA60Command list of Weekly Command Timer Specifications TH-42PF11UK TH-50PF11UKSpecifications TH-58PF11UK TH-65PF11UKPanasonic Professional Flat Panel Display Limited Warranty For the U.S.A and Puerto RicoLimited Warranty Statement For CanadaPage Executive Office Customer’s RecordPanasonic Professional Display Company Panasonic Canada Inc
Related manuals
Manual 60 pages 19.82 Kb
Top Page Image Contents