Panasonic DMR-EH60 warranty Press Enter, Leave this unit in the standby mode

Page 17

Is your cable box now tuned to channel 09?

Yes

No

Test this code again

–If the cable TV box has changed to channel 09, select “Yes” and press [ENTER].

–If the cable TV box is still set to the same channel, select “No” and press [ENTER]. Repeat this step until the cable TV box changes to channel 09.

–If you want to try the code again for some reason, e.g., you accidentally moved the IR Blaster, select “Test this code again” and press [ENTER].

∫The set contents are displayed together

Postal code - L4W 2T3 (Canada)

Cable - Yes

Cable box - No

–If the information is correct, select “Yes, end setup” and press [ENTER].

–If the information is not correct, select “No, repeat setup process” and press [ENTER] to start the setting again.

Once you confirm the input content, the following screen appears.

What would you like to do now?

Watch TV

The above screen may not appear again if you repeat the setup process.

3 Press [ENTER].

A picture or a blue background screen is displayed.

If you do not want to use TV Guide On ScreenTM system

➡57, Auto channel/clock settings

4 Press [Í DVD POWER].

“BYE” appears briefly and then “12:00A” flashes on the unit’s display. This shows the unit is in standby mode. The unit is now ready to download the channel line-up and the program listings.

Check the following again, so the downloading will not fail.

If you connect a cable TV box

≥the output terminal of the cable TV box is connected to this unit’s RF IN or IN3 terminal (➡ 13)

≥the IR Blaster is correctly connected and installed (➡ 13) ≥the cable TV box is turned on

If you do not connect a cable TV box

≥the antenna cable is connected to this unit’s RF IN terminal (➡ 12)

5 Leave this unit in the standby mode.

It is strongly recommended that you wait at least 24 hours before using the unit. No damage will occur if the unit is used sooner, but the channel line-up and program listings may not have been fully downloaded.

≥If you connect a cable TV box, leave it switched on without using it.

≥With some cable TV boxes, the cable TV box remote control can turn on and off both the cable TV box and the television. Utilizing this feature (turning the cable TV box off) will prevent the channel line-up from being downloaded.

≥If the unit’s display changes from flashing “12:00A” to the current time, you can manually set the scheduled recording (➡ 25).

≥If the unit's display does not change to the current time even after waiting, we recommend that you set the clock using “Set Clock Manually” (➡ right).

If you find “There is no data for this screen” displayed on the television when you turn the unit on, the unit has not yet downloaded the channel line-up.

This unit may download

 

 

 

 

 

 

more than one channel

SCHEDULE LISTINGS

SORT

 

SCHEDULE

LISTINGS

SORT

 

 

Channel

8:00PM

8:30PM

 

 

 

TODAY

 

 

 

Last

 

 

 

line-up. Follow the on-

 

 

87

FAVORITES RECORD

INFO.

 

 

NWGB

screen instructions and

There is no data

ducation

 

 

 

 

 

 

TV

 

 

 

 

for this screen.

NWBG

 

 

 

select one of these.

 

 

 

 

 

 

Network

 

 

 

 

 

 

BOX

 

 

 

 

 

 

ANiMe

 

 

 

 

 

 

PBS

 

 

 

Leave the unit in standby mode when you are not using it. The unit will download the necessary data to maintain the listings while it is in standby mode.

Some menus in the SETUP screen no longer need to be set after this unit downloads the television program list. These menus turn grey and become un-selectable. (➡ 54)

To use immediately (Set Clock Manually)

Set the clock manually.

Please note that the program list is not displayed until the unit downloads it. Scheduled recording is only possible manually.

1Press [SETUP].

2Press [3, 4] to select “Setup” and press [1].

3Press [3, 4] to select “Clock Settings” and press [ENTER].

4Press [3, 4] to select “Set Clock Manually” and press [ENTER].

SETUP

 

 

Set Clock Manually

 

Month

 

Day

 

Year

 

Hour

 

Minute

Channel

1

/

1

/

2000

SAT

12

:

00 AM

Setup

 

 

 

 

 

 

 

 

 

Disc

 

 

 

 

 

 

 

 

 

Video

 

 

 

 

 

 

DST

 

Time Zone

Audio

 

 

 

 

 

 

Off

 

EST

Display

 

 

 

 

 

 

 

 

 

TV Screen

ENTER

 

 

 

 

 

 

 

 

5Press [2, 1] to select the item you want to change and press [3, 4] to change the setting.

6Press [ENTER]. The clock starts.

7Press [SETUP].

≥DST (Daylight Saving Time): On or Off

If you select “On”, the clock is advanced one hour starting at 2 a.m. on the first Sunday in April and ending at 2 a.m. on the last Sunday in October.

≥Time Zone shows the time difference from Greenwich Mean Time

(GMT).

 

EST (Eastern Standard Time)

l GMT j5

CST (Central Standard Time)

l GMT j6

MST (Mountain Standard Time) l GMT j7

PST (Pacific Standard Time)

l GMT j8

AST (Alaska Standard Time)

l GMT j9

HST (Hawaii Standard Time)

l GMT j10

If further assistance is needed,

Call 1-800-561-5505.

In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc. TV Guide On Screen, G-LINK, VCR Plusr and PlusCode are registered marks of Gemstar-TV Guide International and/or one of its affiliates.

The TV Guide On Screen and VCR Plusr systems are manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates.

GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES ARE NOT IN ANY WAY LIABLE FOR THE ACCURACY OF THE PROGRAM SCHEDULE INFORMATION PROVIDED BY THE TV GUIDE ON SCREEN SYSTEM. IN NO EVENT SHALL GEMSTAR- TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES BE LIABLE FOR ANY AMOUNTS REPRESENTING LOSS OF PROFITS, LOSS OF BUSINESS, OR INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE PROVISION OR USE OF ANY INFORMATION, EQUIPMENT, OR SERVICES RELATING TO THE TV GUIDE ON SCREEN SYSTEM.

The TV Guide On Screen and VCR Plusr systems are protected by one or more issued United States patents such as 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121; 6,466,734; 6,430,359; 6,091,882; 6,049,652; 5,335,079; 5,307,173; 6,498,895; 6,418,556.

Getting started

RQT8307

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Example Warranty can be found onImportant Safety Instructions Useful features Table of contentsHDD Hard disk drive handling care Inserting/Removing the SD card Disc and card handlingUnit care SAP Using DVD-R, DVD-RW and +R on this unitPlaying the disc on other DVD players Batteries Use AccessoriesRemote control HDD and discs you can use for recording and play HDD, disc and card informationPlay-only discs 12 cm 5z/8 cm 3z DVD Video Recording format DVD-Video formatDiscs that cannot be played Cards useable on this unitType Data that can be recorded and played InstructionsThese operations are also possible… ≥Changing channels RQT8307 Press the Smart Wheel lightly when turning itMain unit Power button Power Í/IUnit’s display Opening the front panelConnection with a television and video cassette recorder When the unit is not to be used for a long timeTo enjoy even higher picture quality Sec. Quick Start for Recording & EPG DisplayConnection with a cable TV box and video cassette recorder Setting the IR BlasterTo enjoy even higher picture quality ConnectionConnection for transferring dubbing from video tape If the antenna connector doesn’t match Connecting an amplifier or system componentFollowing the on-screen messages Press Í DVD PowerInput the operating environment for Your televisionPress Enter Leave this unit in the standby modeSet contents are displayed together Press 3, 4 to select the item and press Enter Selecting television typeReturn ≥Aspect 43/AspectPress 3, 4 to select Setup Press SetupPower saving function Television operationRecording television programs After recording Recording modes and approximate recording timesBefore recording Press Audio Selecting audio to recordFlexible Recording Recording for High-Speed DubbingPlaying while you are recording Press the Green button Scheduled recordingPress TV Guide Press 3, 4, 2, 1 to selectTo cancel recording when it has already begun Enter the settingsManually programming scheduled recordings Press ScheduleDubbing Using VCR Plusi system to make scheduled recordingsScheduled recording Press 3, 4 to select the program Check, change or delete a programRegistering a program you don’t want to miss as Favorite Utilizing the TV Guide On ScreenTM systemTo change to the selected channel Change channel display menu-CHANNEL Setup screenMessages screen Promotions screenPlaying recorded video contents/Playing play-only discs Operations during play Changing audio during play Simple editing operations during playUsing the tree screen to find a group Using menus to play MP3Press TOP Menu Press 3, 4 to select the track and press EnterPlaying still pictures JPEG/TIFF Play Useful functions during still picturePress Display Using on-screen menus/FUNCTIONS window and Status messageUsing on-screen menus Press 3, 4 to select an item Functions windowStatus messages Press StatusEditing titles/chapters and playing Editing titles/chaptersChapters Press 3, 4, 2, 1 to select the chapterCombine Title operationsChapter operations Press 2, 1 to select the source title and press Creating, editing and playing playlistsPress 2, 1 to select the position to Creating playlistsPress SUB MENU, then 3, 4 to Editing and playing playlists/chaptersSelect the operation and press Enter Playlist operationsPicture and folder operation Editing still picturesTransferring dubbing speed mode types and features Transferring dubbing modeTransferring dubbing titles or playlists Transferring dubbing directionOne Touch Transfer dubbing Set the recording modeSet the transfer dubbing direction Transferring dubbing titles or playlistsPress 3, 4 to select Start Dubbing and press Enter When the top menu is displayed ≥If you are not going to change the setting stepSet Time Limit DVD-V HDDManual recording Recording from a video cassette recorderStart play on the other equipment Press ¥ RECTransferring dubbing still pictures Transferring dubbing using the transferring dubbing listRegister still pictures for transfer dubbing To register individual still picturesStructure of folders displayed by this unit To select another folderFolder and press Enter Press 2, 1 to select SD HDD or RAMSetting the protection Common proceduresHDD, disc and card management Providing a name for a discErasing all titles and playlists-Erase All Titles Erasing all the contents of a disc or card-FormatPress 3, 4 to select Finalize Enabling discs to be played on other equipmentPress 2, 1 to select Yes Press 2, 1 to select StartShow Enter Name screen Entering textPress 3, 4, 2, 1 to select a character and press Enter Press SetSummary of settings Changing the unit’s settingsSetup Press 3, 4 to select the tab and pressVideo Tabs Menus Changing the unit’s settingsScreen DTSAdjust Time Zone Auto channel/clock settingsPress To select s1 or r1 CH WPress 3, 4 to select the caption and press Channel captionsPress 3, 4 to select the first character and press Press 2, 1 to return to the Channel Number columnOn the unit’s display MessagesOn the television PCM DTS Frequently asked questionsCover TV Guide On Screen TM system Troubleshooting guide Low volume Picture quality when adjustedCannot switch audio Remote control doesn’tTroubleshooting guide TV Guide On ScreenTM system As soon as the unit is turned On, and when you try to startScheduled recording, the TV Display No ListingTitle operation Start point Cannot erase chapters ≥This occurs as scenes change during Quick ViewTiff SpecificationsGlossary Product information Product ServiceWarranty Service Limited WarrantyIf YOU Ship the Product to a Servicentre Panasonic Canada IncMemo Index
Top Page Image Contents