Panasonic TH-50PHW6, TH-42PHW6 manual Connections, Speakers, AC cord fixing

Page 6

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

(Example: TH-42PHW6)

Speakers (Optional accessories)

SPEAKERS

Terminals (L)

1
2	1
	1
	2

SPEAKERS Terminals (R)

AC cord connection (see page 12)

– AC cord fixing

1. Open the clamper.	2. Insert the AC cord and	3. Slide up the clamper and fix
	close the clamper	the AC cord plug securely.
	securely.	When loosen
		When loosen
		the clamper:
Clamper	AC cord

Note: The power plug in the illustration may not be the type fitted to your set.

– Cable fixing bands Secure any excess cables with bands as required.

Pass the attached cable fixing band through the clip as shown in the figure.

To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.

While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.

1

2

To tighten:

To loosen:

Push the catch

Pull

Pull

R AUDIO L	VIDEO	R AUDIO L PR/CR/R PB/CB/B	Y/G	AUDIO
AV IN	S VIDEO	COMPONENT/RGB IN		AUDIO
AV IN	S VIDEO	COMPONENT/RGB IN
SLOT1	SLOT2	SLOT3	PC IN	SERIAL

Optional Terminal Board Insert Slot (covered)

AV Terminals (see page 9)

COMPONENT/RGB IN and Audio IN Terminals (see page 9)

From EXTERNAL monitor terminal on Computer (see page 7)

From SERIAL Terminal on Computer (see page 8)

Note: At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.

6

Image 6

Contents English Operating InstructionsHigh Definition Plasma Display Model No. TH-42PHW6Table of Contents Important Safety NoticeSafety Precautions SetupWhen using the Plasma Display Electric shocks can result if this is not done Cleaning and maintenanceIf problems occur during use Trademark CreditsAccessories Accessories SupplyRemote Control Batteries Terminals L Speakers Terminals R AC cord connection see ConnectionsSpeakers AC cord fixingSDA Signal Names for D-sub 15P ConnectorPC Input Terminals connection HD/SYNCSerial Terminals connection Installing the ferrite core Large sizeCommand Communication parametersVideo VCR Camcorder AV & Component connectionDVD VCRBasic Controls Off Connecting the plug to the Wall Outlet Power On/Off and input signal selectionPower On/Off AC cord connectionINPUT1 INPUT2 INPUT3 Select the input signalSelecting the On-Screen Menu Language EnglishusOn-Screen Menu Displays To Signal screen for Component see To Signal screen for RGB seeTo setup Screensaver see page 20 Aspect Controls Adjusting Picture Pos./Size Adjusting screenHelpful Hint N / Normalise Normalisation Dynamic Picture AdjustmentsNormal CinemaSound Adjustment MuteScreensaver For preventing after-images Mode selectionStart setting Reversal / Scroll selectionSide Panel Adjustment This function may be applicable to the non-picture areaPress to change the Input label Reduces power consumptionCustomizing the Input labels INPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB33D Y/C Filter For Ntsc AV images Setup for Input SignalsComponent/RGB-in select RGBIf the picture image becomes unstable Colour system / Panasonic AutoCinema reality PAL Secam NtscFreq. kHz/V-Freq. Hz Setting RGB sync signalSync Displays the H Horizontal/V Vertical frequenciesTroubleshooting Plasma Display panel Symptoms CheckVIDEO/COMPONENT/RGB/PC Input Signals Applicable input signals for PC Input D-sub 15P ∗ MarkPAL60 Specifications Customer’s Record