Panasonic TH-42PW5 manual PC Input Terminals connection, Connections

Page 10

Connections

PC Input Terminals connection

If tuner is connected the PC connection is disabled.

COMPUTER

AUDIO

PC IN

	Conversion adapter	Less than	Ferrite core (large size)
	(if necessary)	3" 15/16	(supplied)
		(10 cm)	D-sub 15p
			RGB
			PC cable
	Ferrite core (small size)		Less than
	Ferrite core (small size)		3" 15/16
		(supplied)	(10 cm)
	Audio
			Stereo plug
	Connect a cable which matches
	the audio output terminal on the computer.
Installing the ferrite core (Small size)
1	2	3
		Open
	Pull back the tabs		Press the cable
	Pull back the tabs		through and close
	(in two places)		through and close
	(in two places)
Installing the ferrite core (Large size)
1	2	3
		Open

Pull back the tabs

Press the cable

(in two places)

Notes:

through and close

(1)Computer signals which can be input are those with a horizontal scanning frequency of 15.6 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

(2)The display resolution is a maximum of 640 ⋅ 480 dots when the aspect mode is set to “4:3”, and 852 ⋅ 480 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

(3)The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection.

(4)Some PC models cannot be connected to the set.

(5)There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.

(6)The computer shown in the illustration is for example purposes only.

(7)Additional equipment and cables shown are not supplied with this set.

(8)Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

10

Image 10

Contents Progressive Wide Plasma Display Operating Instructions TH-37PW5English Dear Panasonic Customer Table of Contents For Your SAFETY, Please Read the Following Text Carefully Important Safety NoticeThis Apparatus Must be Earthed Setup Important Safety NoticeWhen using the Plasma Display If problems occur during use Cleaning and maintenanceElectric shocks can result if this is not done Optional Accessories AccessoriesAccessories Supply Check that you have the accessories and items shownObserve the following precaution Remote Control BatteriesPrecaution on battery use Helpful HintTerminals R Terminals L AC cord connection see ConnectionsSpeakers Cable fixing bandsPC Input Terminals connection Installing the ferrite core Small sizeInstalling the ferrite core Large size ConnectionsGND Ground Signal Name Signal Names for D-sub 15P ConnectorSDA HD/SYNC SCL Communication parameters CommandSerial Terminals connection Basic format for control dataBasic Controls Connecting the AC cord plug to the Plasma Display Power On/Off and input signal selectionPower On/Off Connecting the plug to the Wall OutletSelecting the On-Screen Menu Language Select the input signalPower On/Off and input signal selection AV RGB PCOn-Screen Menu Display from Remote Control To setup Screensaver see On-Screen Menu Display from Remote ControlSee page 32 Component see To Signal screen for PC see To setup Multidisplay screen seeAspect mode changes each time the Aspect button Aspect ControlsJust Aspect ControlsZoom PanasonicSize/Clock Phase Adjusting Picture Pos./SizeAdjusting screen Press to exit from adjust modeHelpful Hint N / Normalise Normalisation Adjusting Picture Pos./SizeSize Clock Phase RGB/PC in Mode PosBass Sound AdjustmentMute TrebleOn Off Surround ControlsSurround Surround Button Dynamic Picture AdjustmentsNormal CinemaAdvanced Settings Picture AdjustmentsSet up Timer Present Time SetTimer Set Setup TimerReversal / Scroll selection Mode selectionScreensaver For preventing after-images To stop the Screensaver under On, press the buttonSide Panel Adjustment Setup of Screensaver TimeScreensaver For preventing after-images Press to display the Setup menu screen Setup for Multi DisplayHow to Setup Multi Display Multi Display Setup Press to selectSetup for Multi Display Press to select 2 ⋅ 2, 3 ⋅3D Y/C Filter For Ntsc AV images Setup for Input SignalsComponent/RGB-in Select ComponentPulldown Setup for Input SignalsColour system / Panasonic Auto If the picture image becomes unstableSetting PC sync signal Setup for input signals SyncSetting RGB sync signal Freq. kHz/V-Freq. HzTroubleshooting Plasma Display panel Symptoms CheckSpeaker Connection to the Optional Terminal BoardTerminals R AV Input Terminals connection Connect the signal source equipmentVideo 4 pin socket Example When connecting 21 pin scart cables Component signals Y, PB, PR connectionComponent/RGB Input connection RGB signal R, G, B, HD, VD connection Dedicated Receiver connection AV input Component/RGB input PC RGB input Input signal can be displayedAV/Component /RGB/ PC input signals PAL60Specifications Mass Weight SpecificationsDimensions TH-37PW5 TH-42PW5 Optional SuppliedCustomer’ Record