Panasonic TH-42PW5 manual Remote Control Batteries, Helpful Hint, Precaution on battery use

Page 8

Remote Control Batteries

Requires two R6 batteries.

1.Turn the transmitter face down. Press and slide off the battery cover.

2.Install the batteries as shown in the battery compartment. (Polarity + or – must match the markings in the compartment.)

3.Replace the cover and slide in reverse until the lock snaps.

Two "R6" size

Helpful Hint:

For frequent remote control users, replace old batteries with

Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.

Observe the following precaution:

1.Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.

2.Do not combine a used battery with a new one.

3.Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4.Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

5.Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.

8

Image 8

Contents English Operating Instructions TH-37PW5Progressive Wide Plasma Display Dear Panasonic Customer Table of Contents This Apparatus Must be Earthed Important Safety NoticeFor Your SAFETY, Please Read the Following Text Carefully When using the Plasma Display Important Safety NoticeSetup Electric shocks can result if this is not done Cleaning and maintenanceIf problems occur during use Accessories Accessories SupplyOptional Accessories Check that you have the accessories and items shownRemote Control Batteries Precaution on battery useObserve the following precaution Helpful HintConnections SpeakersTerminals R Terminals L AC cord connection see Cable fixing bandsInstalling the ferrite core Small size Installing the ferrite core Large sizePC Input Terminals connection ConnectionsSDA HD/SYNC SCL Signal Names for D-sub 15P ConnectorGND Ground Signal Name Command Serial Terminals connectionCommunication parameters Basic format for control dataBasic Controls Power On/Off and input signal selection Power On/OffConnecting the AC cord plug to the Plasma Display Connecting the plug to the Wall OutletSelect the input signal Power On/Off and input signal selectionSelecting the On-Screen Menu Language AV RGB PCOn-Screen Menu Display from Remote Control On-Screen Menu Display from Remote Control See page 32 Component see To Signal screen for PC seeTo setup Screensaver see To setup Multidisplay screen seeAspect mode changes each time the Aspect button Aspect ControlsAspect Controls ZoomJust PanasonicAdjusting Picture Pos./Size Adjusting screenSize/Clock Phase Press to exit from adjust modeAdjusting Picture Pos./Size Size Clock Phase RGB/PC in ModeHelpful Hint N / Normalise Normalisation PosSound Adjustment MuteBass TrebleSurround Surround Button Surround ControlsOn Off Picture Adjustments NormalDynamic CinemaAdvanced Settings Picture AdjustmentsSet up Timer Present Time SetTimer Set Setup TimerMode selection Screensaver For preventing after-imagesReversal / Scroll selection To stop the Screensaver under On, press the buttonScreensaver For preventing after-images Setup of Screensaver TimeSide Panel Adjustment Setup for Multi Display How to Setup Multi DisplayPress to display the Setup menu screen Multi Display Setup Press to selectSetup for Multi Display Press to select 2 ⋅ 2, 3 ⋅Setup for Input Signals Component/RGB-in Select3D Y/C Filter For Ntsc AV images ComponentSetup for Input Signals Colour system / Panasonic AutoPulldown If the picture image becomes unstableSetup for input signals Sync Setting RGB sync signalSetting PC sync signal Freq. kHz/V-Freq. HzTroubleshooting Plasma Display panel Symptoms CheckTerminals R Connection to the Optional Terminal BoardSpeaker Video 4 pin socket Connect the signal source equipmentAV Input Terminals connection Component/RGB Input connection Component signals Y, PB, PR connectionExample When connecting 21 pin scart cables RGB signal R, G, B, HD, VD connection Dedicated Receiver connection Input signal can be displayed AV/Component /RGB/ PC input signalsAV input Component/RGB input PC RGB input PAL60Specifications Specifications DimensionsMass Weight TH-37PW5 TH-42PW5 Optional SuppliedCustomer’ Record