Panasonic PT-F100E Lamp Runtime, Power OFF Timer, Control Panel, Auto Setup, Direct Power on

Page 37

OPTION menu

LAMP RUNTIME

You can check how long the lamp has been used.

NOTE:

•LAMP RUNTIME is a relevant matter for lamp replacement timing. See “Replacing the Lamp unit” on page 43.

•When the lamp unit is replaced with the new one (ET-LAF100), the setting will be reset to “0”.

POWER OFF TIMER

You can set the off timer to switch off the POWER of the projector after a certain period of time automatically when no signal is detected. Press I H to select the required period from 15 to 60 minutes at intervals of

5 minutes.

DISABLE

15 MIN.

 

 

 

 

60 MIN.

 

 

 

 

 

 

 

 

 

 

 

CONTROL PANEL

You can turn off the function of the control panel buttons on the projector body. Press I H to select the required option.

INVALID

Invalidate the control panel buttons

 

Confirmation screen will be

 

displayed.

VALID

Validate the control panel buttons

AUTO SETUP

You can turn off the AUTO SETUP function for when the COMPUTER signal is detected.

AUTO

When the projector detect a

 

COMPUTER signal, adjust the

 

projected image position

 

automatically for SIGNAL SEARCH,

 

DOT CLOCK and CLOCK PHASE.

BUTTON

Only when the AUTO SETUP button

 

is pressed, the projected image

 

position will be adjusted for DOT

 

CLOCK and CLOCK PHASE. See

 

“Remote control” on page 13.

20 MIN.

 

 

 

 

 

 

55 MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25 MIN.

 

 

 

 

 

 

50 MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30 MIN.

 

 

 

 

 

 

45 MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

35 MIN.

 

 

 

 

 

 

40 MIN.

 

 

 

 

 

 

 

 

 

 

 

 

DIRECT POWER ON

You can switch the projector start up status for when the Mains lead is connected while the MAIN POWER is on, or for when the MAIN POWER is switched on while the Mains lead is connected. Press I H to select the required option.

OFF

The projector will start from the

 

standby mode or the projecting

 

mode.

ON

The projector will start from the

 

projecting mode.

NOTE:

• Usually the recommended setting is AUTO.

SIGNAL SEARCH

You can turn off the auto signal detecting system.

ON

Detect the input signal from the

 

terminals and project the image.

OFF

Deactive

NOTE:

•SIGNAL SEARCH is not available when any input signal is projecting.

•Usually the recommended setting is ON.

INSTALLATION

When installing the projector, select the projection method according to the projector position. Press I H to cycle through the options. See “Projection method” on page 17.

Settings

NOTE:

•When the projector is started from the projecting mode, pressing the POWER button procedure is skippable.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting in the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting in the ceiling and

projecting from rear

 

 

 

ENGLISH - 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents PT-F100E Model number PT-F100NTE / PT-F100E Important Safety NoticeThis Apparatus Must be Earthed To rain or moistureFor business users in the European Union Important Safety NoticeDeclaration of Conformity Important Safety InformationImportant Infomation Contents Maintenance SettingsContents AppendixPrecautions with regard to safety Do not set up the projector outdoors Precautions with regard to safetyDo not look into the lens while the projector is being used Use only the specified batteriesDo not put your weight on this projector Remove the used batteries from the remote control promptlyDo not mix old and new batteries Electric shocks can result if this is not doneAccessories Read this first Minimum required setting screenAbout Your Projector Remote controlAbout Your Projector Projector bodyTop and front view Control panelComputer. Selectable for input About Your Projector Back and bottom viewOutput by menu operation Calculation methods for screen dimensions Setting upScreen size and throw distance Projected imageSetting up Front leg adjusters and throwing angleProjection method Mounting in the ceiling and projecting from frontLens shift and positioning Adjusting the Lens shift leverHorizontal shift Vertical shiftWhen the screen position is fixed Setting up Projector location rangeWhen the projector position is fixed Connections Connecting with computersBefore connection to the projector LAN terminalConnecting with Video IN/S-VIDEO Connecting with AV equipmentConnecting with Component ConnectionsPower indicator Switching the projector on/offMains lead Switching off the projector Switching on the projectorSwitching the projector on/off Switch the Main Power on Press the Power buttonProjecting an image Selecting the input signalPositioning the image Focus lever Zoom leverSetting up the image position automatically Remote control operationOperating range Facing to the projectorUsing the laser pointer Switching the input signalProjecting an image in INDEX-WINDOW mode Resetting to the factory default settingsCapturing an image Stopping the projection temporaryEnlarging the centred area Controlling the volume of the speakerEnlarging the image Shifting the centre pointMenu Navigation Adjusting with the bar scale itemsNavigating through the Menu Displaying the Main menuMenu Navigation Main menu and Sub-menuNetwork Standby Live Mode CUT Status InitialiseWEB Control Picture menu For S-VIDEO/VIDEO signals Detailed SetupFor RGB signals Position menu Resizing When the Resizing is set to OFFFrame Lock Position menuOption menu Auto Setup Power OFF TimerDirect Power on Signal SearchTest Pattern HighlandPassword Change Input PasswordSecurity menu Text DisplayItems in Network menu Network menuNetwork menu, the following items are available Managing the indicated problems TEMP, Lamp and Filter IndicatorsLamp indicator Temp indicatorCleaning the projector Care and ReplacementReplacing the ARF Auto Rolling Filter When to replace the Lamp unit Care and Replacement Resetting the FilterReplacing the Lamp unit Before replacing the Lamp unitCare and Replacement Replacement procedure Ceiling mount bracket safeguardsInstalling the safety cable Removing and replacing the lamp unitTroubleshooting Technical Information List of compatible signalsQuality*2 Dots*1 KHz MHzSerial terminal Control commands Technical Information Cable specificationsComputer connection guidance ProjectorSwitching input Signals Lamp switchingInput signal Remote terminalSpecifications OUT COMPONENT1Audio Computer AudioSW m = SD x SH m = SD x LW m = 0.0332 x SD LT m = 0.066 x SD Screen size and throw distance for 169 aspect ratioTrademark acknowledgements DimensionsUnit mm These Operating Instructions are printed on recycled paperALS Ambient Luminance Sensor ARF Auto Rolling Filter IndexCalculation methods LeverIndex S0207-2067C
Top Page Image Contents