Panasonic PT-LB51E, PT-LB51NTE operating instructions Accessories

Page 11

Precautions with regard to safety

Cautions on use

Important Information

In order to get the best picture quality

Draw curtains or blinds over any windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen.

Do not touch the surfaces of the lens with your bare hands.

If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen.

Liquid crystal panel

Do not project the same image for long periods of time, as this may remain as an afterimage on the liquid crystal panel.

The liquid crystal panel of the projector is built with very high precision technology to provide fine picture details. Occasionally, a few stuck pixels may appear on the screen as fixed points of blue, green or red. It is recommended to switch off the projector once and try after 1hour later again. Please note that this does not affect the performance of your LCD.

Screen

Do not apply any volatile substances which may cause discolouration to the screen, and do not let it become dirty or damaged.

The projector has a high pressure mercury lamp and that is characterised as follows.

The brightness of the lamp depends on the duration of use.

The lamp may explode or shorten the lamp life by shocks or chipping damage.

The lamp may explode only occasionally after using the projector.

The lamp may explode if using the projector after the instructed lamp replacement timing.

The lamp life is depends on individual lamp characteristics, usage condition and the installation environment. Especially the consecutive use of the projector for more than 10 hours, or the frequent switching on or off may greatly affect on the lamp life.

Optical components

If you use the projector consecutively 6 hours every day, the optical components may need to be replaced in less than 1 year.

Accessories

Make sure the following accessories are provided with your projector.

Remote control*

PT-LB51NTE :

N2QAYB000169 (X1)

PT-LB51E:

N2QAYB000172 (X1)

AUTO

SETUP

INPUT

SELECT

COMPUTER WIRELESS VIDEO

WIRELESS PAGE

PRESENTATION

MENU RETURN

ENTER

FREEZE SHUTTER

COMPUTER

DEFAULT SEARCH INDEX-WINDOW

Mains lead (x1)

AA batteries for

RGB signal cable (x1)

TXFSX02QHUZ

Remote control (x2)

[1.8 m (5’ 10”),

 

 

K1HA15DA0002 x1]

Carrying bag (x1)

CD-ROM* (x1)

(TPEP018)

TQBH9009

MULTI-LIVE

DIGITAL ZOOM VOLUME

*The illustration above is the remote control unit for the PT-LB51NTE.

*PT-LB51NTE only

ENGLISH - 11

Image 11
Contents PT-LB51E To rain or moisture Important Safety NoticeModel number PT-LB51NTE/PT-LB51E This Apparatus Must be EarthedFor business users in the European Union Important Safety NoticeDeclaration of Conformity DoC Declaration of ConformityImportant Infomation Contents Appendix SettingsMaintenance Precautions with regard to safety Use only the specified batteries Precautions with regard to safetyDo not set up the projector outdoor Do not look into the lens while the projector is being usedDo not mix old and new batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Accessories Top view Remote controlBattery compartment About Your ProjectorAttaching a hand strap About Your ProjectorControl panel Projector bodyTop and front view Back and bottom view Connector PanelProjected image Screen Setting upCalculation methods for screen dimensions Screen size and throw distanceMounting in the ceiling and projecting from front Front adjustable legs and throwing angleSetting up Projection methodBefore connection to the projector Connecting with computersConnections Connections Connecting with AV equipmentConnecting with Video IN/S-VIDEO Connecting with ComponentMains lead Switching the projector on/offGreen Power indicatorSwitching the projector on/off REDPlug the Mains lead into the projector Switching on the projectorPress the Power button Switching off the projector Positioning the image Selecting the input signalProjecting an image Facing to the projector Remote control operationSetting up the image position automatically Operating rangeStopping the projection temporary Switching the input signalCapturing an image Changing the image size Resetting to the factory default settingsProjecting an image in INDEX-WINDOW mode Switching the positionShifting the centre point Controlling the volume of the speakerEnlarging the centred area Enlarging the imageNavigating through the Menu Menu NavigationMenu Navigation Main menu and Sub-menuOnly Live Mode CUT Status InitializeSee CD-ROM contents for detailed information Picture menu Daylight View Detailed SetupFor RGB signals For S-VIDEO/VIDEO signalsPosition menu Frame Lock S1 video signalsLanguage menu ResizingOption menu Direct Power on Power OFF TimerAuto Setup Signal SearchSolid blue You can perform more detailed setting in various itemsHighland Semi transparent blackText Display Password ChangeInput Password Security menuWireless menu, the following items are available Items in Wireless menuTemp indicator TEMP, Lamp IndicatorsManaging the indicated problems Lamp indicatorReplacing the air filter Care and ReplacementCleaning the projector Before replacing the Lamp unit Care and ReplacementWhen to replace the Lamp unit Replacing the Lamp unitHandles lamp unit fixing screws Lamp unit cover Lamp unit cover fixing screwsTroubleshooting Technical Information List of compatible signalsSerial terminal Projector Technical Information Cable specificationsControl commands Apple Manufacturer Key commandComputer connection guidance PanasonicSpecifications Variable Audio OUTAudio Computer AudioDimensions Trademark acknowledgements Navigation buttons IndexMains lead Screen size Remote controlIndex Ring