Panasonic TH-37PH10UK manual Safety Precautions / Maintenance, Setup, AC Power Supply Cord

Page 7

Safety Precautions / Maintenance

WARNING

Setup

Do not place the Plasma Display on sloped or unstable surfaces.

• The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

•If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

•Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.

Transport only in upright position!

•Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, 2 3/8” (6 cm) or more at the bottom, and 2 3/4” (7 cm) or more at the rear. If using some other setting-up method, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 2 3/4” (7 cm) or more at the rear.

AC Power Supply Cord

The Plasma Display is designed to operate on 120 V AC, 50/60 Hz.

Do not use any power supply cord other than that provided with this unit.

• Doing so may cause fire or electric shocks.

Securely insert the power cord plug as far as it will go.

•If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

•Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately.

•Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

•A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

Maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

•If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

•Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

•If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

•Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

•Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents English Español Operating Instructions Manual de instruccionesModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC StatementWhen using the Plasma Display Safety PrecautionsAC Power Supply Cord MaintenanceSafety Precautions / Maintenance SetupAccessories Supplied AccessoriesRemote Control Batteries Speakers ConnectionsAC cord fixing PC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorConnections Basic format for control data CommandSerial Terminals connection Communication parametersAV & Component / RGB connection RGB signal R, G, BFix the AC cord plug securely to the Plasma Display. see Power on / OFFConnecting the AC cord plug to the Plasma Display Connecting the plug to the Wall OutletBasic Controls Basic Controls On-Screen Menu Displays VA N C E D SettingsOn Time / Power OFF Time / Power OFF TimeOn-Screen Menu Displays INPUT1A INPUT1B INPUT2 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageDuring Multi PIP Operations Aspect ControlsNormal Zoom Full Panasonic AutoEliminate the flickering and distortion Adjusting POS. /SIZEClock Phase RGB/PC in modeMulti PIP 1280x768@60Hz DVI Advanced PIPOne screen Advanced PIP Press to exit from Options menu Sub screen Main screenStandard Cinema Dynamic Picture AdjustmentsAdvanced Settings on Advanced Settings OFFEffect Details Advanced SettingsPicture Adjustments Effect AdjustmentsMute Sound AdjustmentSelect the magnification required for the enlarged display Digital ZoomDisplay the operation guide PositionPress to set up DAY or Present Time of DAY Present Time SetupButton Forward Display the SET UP Timer Screen Press to select SET UP TimerPower on Time / Power OFF Time Negative / Scroll selection Mode selectionStart setting Screensaver For preventing image retentionReduces screen image retention Setup of Screensaver TimeScreensaver For preventing image retention OFF Dark MID Bright Side BAR AdjustPress to exit from Screensaver Customizing the Input labels Reduces power consumptionAddition sign Selected Input Press to select × 1, × 2, × 3, × SET UP for Multi DisplayHow to setup Multi Display Press to select Vertical ScaleDisplay Number locations for each arrangement Examples SET UP for Multi DisplayID Cancellation Seam Hides Video SettingID Remote Control Function ID remote control button operationSelect SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesColor System / Panasonic Auto SET UP for Input SignalsPulldown / Video NR FREQ. kHz / V-FREQ. Hz Setting RGB sync signalSync Refresh RateOptions1/3 Options AdjustmentsOff Initial VOL Sets normal volume Level Options AdjustmentsEnable Normalization Weekly Command Timer Press to set each item Press to select a command numberPress to select Time / Command Time Set the time to execute a command programShipping condition Plasma Display panel TroubleshootingRGB VIDEO/COMPONENT/RGB/PC input signalsVideo input PAL60Command list of Weekly Command Timer TH-37PH10UK TH-42PH10UK SpecificationsTH-50PH10UK TH-58PH10UK SpecificationsLimits and Exclusions Limited Warranty Statement Panasonic Canada Inc Customer’s RecordPanasonic Broadcast & Television Systems Company Executive Office
Related manuals
Manual 53 pages 52.12 Kb
Top Page Image Contents