Kenwood RC-R0507 instruction manual Getting the most from your remote control

Page 3

Getting the most from your remote control

RC-R0507 (En/T)

The remote control supplied with this receiver is also capable of controlling components from a variety of manu- facturers once you register the appropriate setup codes into the remote control unit.

Refer to "Remote operation of other components" for de- tails about the operations available for each component.

Low battery warning

Replace all four batteries with new ones when you notice a shortening of the distance from which the remote control will operate or if the remote control blinks 5 times when you press a key. The remote control is designed to retain setup codes in memory while you change batteries.

Registering setup codes for other components

3

3Press the VIDEO, AUDIO, or TV key repeatedly to select the desired component.

VIDEO key

AUDIO key

TV key

 

 

1VIDEO1 (VCR1)

 

 

1CD (CD)

 

 

1TV1

 

 

 

 

 

 

 

2VIDEO2 (VCR2)

 

 

2TAPE or MD

 

 

2TV2

 

 

 

 

 

 

 

 

 

 

3VIDEO3 (DVD)

 

 

(TAPE)

 

 

3CABLE

 

 

 

 

 

 

 

 

or DVD 6ch

 

 

3PHONO

 

 

 

 

 

 

 

 

 

Example : To register the component connected to the VIDEO 1 jacks, select "VIDEO 1 (VCR1)".

On models other than the KRF-V8010D,DVD 6ch” is displayed instead of “VIDEO 3”. It is possible to enter a setup code for the DVD 6ch input, but the display indication will remain “DVD 6ch”. It is not possible to change the name of this input.

VIDEO, AUDIO, TV

1-0

POWER

 

 

VCR1￿￿￿ ￿ ￿

SP A

L

R

 

 

SW

 

4Use the numeric keys to enter the setup code.

Example: Press "5258" to register a LD player made by KENWOOD.

The backlight flashes once each time a number is entered.

ENT

• If an invalid setup code is entered the remote will output one long

blink, disregard that code and return to the beginning of step 4.

 

 

• If you push an invalid key, the remote will exit the setup mode.

1Find the setup code of the component to be registered.

• Refer to the setup code lists to find the setup code for the

component to be registered.RC7 Example: To register a CD made by KENWOOD, you would enter "8028".

When registering setup codes for KENWOOD audio components which are connected to this unit by system control cords, use the following codes to insure proper system control operation:

Cassette: 7000, CD: 8099, MD: 9000.

Input

Component

Maker

Code

Key

 

 

 

 

 

(CD)

CD player

KENWOOD

8028, 8037

AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TV 1

 

 

 

 

 

 

 

 

 

TV 2

 

 

 

 

 

 

 

 

 

CABLE

 

 

 

 

 

 

 

 

2Hold down the ENT key until the backlight flashes twice.

At this time all inputs become available regardless of any earlier registration.

For step 2 through step 8, make sure you start the next step within five seconds of completing the previous one. If more than five seconds elapses between any two steps, you will need to go back and start over from step 2.

5Press the POWER key, and check to see that the compo- nent you want to control turns on.

If the component does not react, and there is more than one setup code, enter another setup code and try again.

PLAY, TUNING/SKIP (+/–) or MULTI CONTROL key can also be used instead of POWER key.

If the component is already on, pressing POWER key will turn it off.

6Press the ENT key to store the code you have just input.

The backlight flashes twice.

This code replaces any previous setup codes entered for the respective component.

7Repeat steps 3 to 6 to register additional components until all components have been registered.

If you have components that are not remote controllable, like a record player (etc.), you will need to register a Non-IR code at the respective input. This keeps the respective input in the remote control's cyclic list so you can select it using the remote control. Please consult the owner's manual of the components you are connecting for information regarding remote controllability. The list of Non-IR codes is included at the beginning of the Setup code chart.

Continued to next page

Remote Control

Image 3
Contents Remote operation of other components Preset Remote Control Quick Start GuideAutomatic input naming Quick Start GuideGetting the most from your remote control Press the operation keys you desire Getting the most from your remote controlLocation. MACRO1, 2, and 3 respectively Make a plan of the macro play you want to SetupPress the Shift key Execute the desired operationsPress the Macro key so that the backlight flashes twice Deleting a setup codeChecking a setup code Press the keys to be operated in orderSetup code chart VCR Setup codesNon-IR codes TV Setup codes Setup code chartSatellite Setup codes Setupcode chart LD player Setup codesCD player Setup codes MD deck Setup codes Cassete deck Setup codesCable Setup codes DAT deck Setup codesRemote Control RC5 Remote control unitCase of difficulty RC3CD player operations Remote operation of other componentsTuner operations Cassette deck operationsSatellite tuner operations TV operationsVCR operations LD player operationsDVD player operations Cable tuner operations