Sharp LC-37HV4M Setting the Display on the wall, Setting the AVC System with the stand

Page 11

Preparation

Setting the Display on the wall

Using an optional bracket to mount the Display

•You can ask a qualified service personnel about using an optional AN-37AG1 bracket to mount the Display to the wall.

•Carefully read the instructions that come with the bracket before beginning work.

Hanging on the wall

AN-37AG1 wall mount bracket. (See the bracket instructions for details.)

Vertical mounting

Angular mounting

CAUTION

•Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel. Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that results in accident or injury.

Setting the AVC System with the stand

How to install the AVC System vertically using the stand unit.

• Use the supplied stand unit for installing the AVC System vertically in an upright position.

Stick each spacer to the		Attach each cushion to		Fit the stand to the AVC
1 stand as shown.		2 the stand as shown.		3 System.
Peel each spacer		Peel each cushion		Insert the stand into the AVC
				System, making sure that the
away from the		away from the
				thick and thin bulges of the
paper and attach	Stand	paper and attach
				stand align with the big and
to the four bulging		to the four areas at
	spacer		Stand cushion	small holes on the AVC
areas on the stand.		the bottom.
	Bulge			System.

			Attaching point	Thin bulge

Bulge				Small	Thick
		Attaching point			bulge
				hole

				Big hole
Attach the stand using the		The AVC System installed
4 stand screws as shown.		vertically with the stand.
	Stand screw

NOTE

•When mounting the AVC System vertically, always use the supplied stand. Be careful not to block vent holes when standing up directly on the floor or a flat surface as this can result in equipment failure.

10

Image 11

Contents LC-37HV4M LC-37HV4M ContentsDear Sharp customer Important Safety PrecautionsPrecautions when transporting the Display Important Safety PrecautionsSupplied accessories Example Attaching right speaker PreparationAttaching the speakers Secure the stand on a platform or the floor How to secure from overturningSecuring from overturning PreparationSetting the System in place Where to place the SystemAVC System rear view Setting the SystemConnecting the system cable and the AC cord to the Display Removing the terminal coverCables come out from the small opening Closing the terminal coverCable clamp Large Cable clamp SmallHanging on the wall Setting the Display on the wallSetting the AVC System with the stand Using an optional bracket to mount the DisplayInserting the batteries Using the remote control unitDisplay Part namesPart names AVC SystemRemote control unit Basic connection Connecting to an antennaConnecting to the power outlet Watching TVWatching TV Turning on the powerTurning off the power Simple button operations for changing channels Using Flashback a on the remote control unitUsing CHa/bon the remote control unit Using 0 9 on the remote control unitMute Simple button operation for changing volume/soundChanging the volume Using eon the remote control unitSRS sound options Watching TV Using hon the remote control unitWatching TV Using Sound on the remote control unit List of AV menu items to help you with operations Basic adjustment settingsAV input mode menu items PC input mode menu itemsPress c/dto select Yes, and then press Auto installationBasic adjustment settings Press a/bto select Password, and then press EnterAutomatic channel sorting Automatic channel searchingAutomatic channel labelling Press a/bto select Auto Search, and then press Enter Programme setupPress a/b to select Programme Setup, and then press Enter Auto searchThen press Enter Basic adjustment settings Manual setting for each channelProgramme Setup Manual menu Press a/b to select Manual Adjust,Fine tuning Search tuningLabelling menu Colour systemLabelling channels Colour system menuLock menu Setting the child lockSkipping channels Skip menuSort menus Basic adjustment settings SortPress a/ b to select Programme Setup Press a/bto select Language, and then press Enter Language setting for on-screen displayPC Input mode AV Input modeGreen Picture adjustmentsSelected item Cbutton Dbutton Contrast RedPress a/bto select C.M.S., and then press Basic adjustment settings S. Colour Management SystemPress a/bto select Advanced, and then press Enter Press a/b to select C.M.S., and then press EnterPress a/bto select the desired level, and then press Enter Basic adjustment settings Colour temperature BlackPress a/bto select Colour Temp, and then press Enter Press a/bto select Black, and then pressFilm mode Basic adjustment settings MonochromePress a/bto select DNR, and then press Basic adjustment settings SettingPress a/ bto select I/P Setting, and then DNR Digital Noise ReductionSurround Audio adjustmentSound adjustment Power save Power ControlPower control for AV source No operation Off No signal OffPress a/b to select No Signal Off, and then press Enter Press c/d to select Enable, and then Press EnterPress Menu and the PC Menu screen displays Basic adjustment settings Power Control for PC sourcePower management Press a/bto select Power Management, and then press EnterAVC System front view Using external equipmentWatching a DVD image Using external equipmentConnecting a DVD player For INPUT1 signal DVD playerDisplaying a VCR image Connecting a VCRFor INPUT2 signal Watching a VCR imageDisplaying broadcasts via an Hdtv tuner Connecting an Hdtv tunerFor INPUT3 signal Watching broadcasts via an Hdtv tunerDisplaying an image of the game console or camcorder Connecting a game console or camcorderEnjoying a game console and viewing camcorder images Displaying an image from a PC Connecting a PCSignal names for 15-pin mini D-sub connecter Viewing an image from a PCMake sure to connect the speaker jack and cable Connecting external speakersWhen using external speakers How to connect the speaker cablePress a/b to select Speaker, and then press Enter Using external equipment Selecting speakersDescription Useful adjustment settingsImage position AV input mode only Moving the picture on the screen Useful adjustment settingsPhase Auto Sync. adjustment PC input mode onlyFine Sync. adjustment PC input mode only For automatically adjusting the PC imageInput selection Input signal sourceInput signal setting Press a/b to select Colour System, and then press Enter Colour system setting AV input mode onlyAV mode selection Signal system of your equipment, and thenAuto Selection Wide mode for AV input modeManual Selection Wide mode for PC input mode Example Input signal PC input mode onlyPress a/bto select Input Signal and then press Enter Press a/bto select the desired input signal on the displayPress a/bto select WSS, and then press Wide screen signalling WSS AV input mode onlyPicture aspect ratio AV input mode only WSS signal 43 screen Mode NormalYou can set the orientation of the picture AV input modePC input mode RotatePress c/d to select Fixed or Variable, and then press Enter Sleep timerAudio out Press a/bto select Audio Out, and then press EnterPress a/bto select Cool Climate, and then press Enter Cool climateClearing the password Password setting for child lock TV mode onlySetting a password Dual screen Useful featuresDual screen functions Press d to exit still image Teletext language settingUseful features Picture and still image Update the still image by pressing EnterTeletext function Useful featuresWhat is Teletext? Teletext modeSubpage screen Useful features Displaying SubpagesDisplaying TOP Overview TOP Overview screenUseful features Time display Appendix TroubleshootingProblem Possible Solution 72 Hz 75 Hz 85 Hz 800g600 56 Hz 60 Hz 832g624 74.5 Hz PC compatibility chartAppendix 640g400 85 Hz 720g400 70 Hz 640g480 60 Hz 65 HzPC Control of the System RS-232C port specificationsResponse code format CommandsPart name Part number SpecificationsOptional accessories 37oLCD Colour TV, ModelLC-37HV4MDisplay Dimensional drawingsDimensional drawings Press a/bto select Auto Installation Press Enter HOW to SET the Factory PresetsSharp Corporation