Sharp LC-42SB55E, LC-32SB25E Special Note for Users in the U.K, Blue Neutral Brown Live

Page 2

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or ASA and of the same rating as above, which is also indicated on the pin face of the plug, must be used.

Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 5A socket outlet, as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.

The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.

Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.

Before replacing the plug cover make sure that:

If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.

The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

( 482.0) / [ 562.0] / [[ 694.0]] ( 482,0) / [ 562,0] / [[ 694,0]]

( 442.0) / [ 522.0] / [[ 654.0]] ( 442,0) / [ 522,0] / [[ 654,0]]

( 40.0) /

[ 40.0] / [[ 40.0]]

( 200.0) / [ 200.0] / [[ 200.0]] ( 200,0) / [ 200,0] / [[ 200,0]]

( 390.0 ) / [ 390.0 ] / [[ 504.0 ]]

( 390,0 ) / [ 390,0 ] / [[ 504,0 ]]

( 652.0) / [ 783.0] / [[ 1009.0]]

( 652,0) / [ 783,0] / [[ 1009,0]]

( 578.0)

/ [ 700.6] / [[ 933.5]]

 

 

/359,3]326,0)[( / [[ 526,2]]

 

 

/359.3][326.0)( / 526.2]][[

( 578,0)

/ [ 700,6]

/ [[ 933,5]]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

( 200.0) / [ 200.0] / [[ 400.0]]

( 200,0) / [ 200,0] / [[ 400,0]]

( ) : 26"

[ ] : 32"

[[ ]] : 42"

( 89.0 ) / [ 94.5] / [[ 99.0]]

( 89,0 ) / [ 94,5] / [[ 99,0]]

( 77.8) / [ 78.5] / [[ 101.0]]

( 77,8) / [ 78,5] / [[ 101,0]]

( 280.4) / [ 323.5] / [[ 392.3]] ( 280,4) / [ 323,5] / [[ 392,3]]

( 235.0) / [ 235.0] / [[ 270.0]]

( 235,0) / [ 235,0] / [[ 270,0]]

Image 2
Contents Sharp Corporation Special Note for Users in the U.K Blue Neutral Brown LiveContents Dear Sharp customer Important Safety PrecautionsIntroduction Remote control unit IntroductionTV Front view TV Rear viewMount the TV Stand Supplied accessoriesPreparation Wall mountingPreparation Installation of batteriesUsing the remote control unit Initial installation overview Quick guideFirst time installation Quick guideWatching TV Switching on/offSelecting Sound mode Daily operationWatching TV Switch on EPGEPG Electronic Program Guide Sample MHEG5 screen Using the MHEG5 application UK onlyTeletext Buttons for teletext operationsIntroduction to connections Connecting external devicesBefore connecting DVI/HDMI conversion Supported video signalVideo connection Connecting external devices Scart connection Speaker/ amplifier connectionGo to Features Common interface Connecting external devicesAccess CI Module service Inserting a CA CardCommon operation Operation without a remote controlMenu operation Picture Adjust picture settingsTV menu Use smart picturesTV menu Change picture format Adjust feature settings FeaturesAdjust sound settings SoundAutomatically switch the TV off Stop time Automatically switch the TV to standby SleeptimerAutomatically switch the TV on Start time Lock TV channels or connected devices Auto LockSelect a subtitle language on digital TV channels Use subtitlesHdmi overscan Listen to digital radio channelsAutomatically install channels InstallationInstall channels Automatic installation or Installation updateSelect your system Manually install channelsInstallation update Search and store new TV channelsRename channels Uninstall or reinstall channelsRearrange channels Test digital receptionFactory reset Update software digital broadcastsAV reset Source LabelsSupported display resolutions Connecting a PCConnecting a PC Analogue ConnectionAppendix TroubleshootingProblem Possible Solution Specification AppendixSoftware developed by Sharp and open source software Other informationTrademarks Obtaining source codeOther Countries outside the EU Information on Disposal for Business Users European Union