Sansui HDLCDVD265 TV operation, To select the video input source, To Select Analog Channels

5 Press EXIT/CANCEL to return to the normal screen.

TV operation

1 To turn on the TV, press POWER. (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.)

2 Adjust the volume level by pressing VOL + or – . The volume level will be indicated on the screen by blue bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of blue bars also decreases.

3 Set the Signal Type option to the appropriate position (see “Air/Cable selection” on page 15).

4 Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2, press 2, then press

ENTER.

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press ENTER.

100-125: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 3 digits, then press the – button, followed by the remaining number.

Example, to select channel 015-001, press 0, 1, 5, –, 0, 0, 1, then press ENTER.

• If a channel is selected with only audio content, “Audio only” will be displayed on the screen.

• If a channel is selected with a weak digital signal, “Digital channel signal strength is low” will be displayed on the screen.

The same program may be available on either an analog channel or a digital channel.You may choose to watch either format.

• If a channel is selected to which you have not subscribed, “Digital channel is encrypted” will be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air		Cable
VHF		VHF
2-13		2-13
UHF	STD/HRC/IRC
14-69	14-36	(A) (W)
	37-59	(AA) (WW)
	60-85	(AAA) (ZZZ)
	86-94	(86) (94)
	95-99	(A-5) (A-1)
	100-135 (100) (135)
	01	(5A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT SELECT, then press ▲/▼ or corresponding Number buttons (0-7), then press ENTER.You can select TV, Video 1, Video 2, Component, HDMI1, HDMI2, PC or DVD depending on which input jacks you used to connect your devices.

Source Selection

0.TV

1.Video 1 2.Video 2 3.Component 4.HDMI 1 5.HDMI 2 6.PC 7.DVD

[0-7]:Select

CH /

Press and release CH / . The channel automatically stops at the next channel set into memory.

For proper operation, before selecting channels, they should be set into the memory. See “Memorizing channels” on pages 15 and 16.

DISPLAY

Press DISPLAY to display the current information on the screen.

When the TV receives a digital signal, the digital information will appear.

	62-001	HDTV Moving Picture1	Sleep Timer
	CH-1		Off
	Digital	Air	English
	No Program Information is available
	Mono
	Full
	1080i
• Channel number				•	Station name
•	Channel label (if preset) •				Broadcast program name
•	V-Chip rating			•	Signal type
•	Sleep timer			•	Audio language
•	Program guide			•	Picture size
•	Resolution

When the TV receives a analog signal, the analog information will appear.

14Sleep Timer

Off

Analog Cable

Mono

Full

480i

•	Channel number	• Channel label (if preset)
•	V-Chip rating	•	Signal type
•	Sleep timer	•	Picture size
•	Audio information	•	Resolution
	(Stereo, SAP or Mono)

Press DISPLAY again to clear the call display.

NOTE:

• After a few seconds, DISPLAY screen will return to normal TV-operation automatically.

RECALL

This button allows you to go back to the last channel selected by pressing RECALL. Press RECALL again to return to the last channel you were watching.

17