Sansui SLED2280 Memorizing channels, Air/Cable selection, Automatic Search, Adding Channel

Select “Channel”, then press ▶ or ENTER.

Press ▲ or ▼ to select “Add/Delete”, then press ▶ or ENTER.

Press ▲ or ▼ to select “Add/Delete”, then press ▶ or ENTER.

Press ▲ or ▼ to select the channel that you want to skip.

Add/Delete

Memorizing channels

This TV is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the TV’s memory. To use this TV with an antenna, set the Signal Type option to the Air mode. When shipped from the factory, this menu option is in the Cable mode.

Air/Cable selection

1 Select “Channel”, then press ▶ or ENTER.

2 Press ▲ or ▼ to select “Auto Ch Memory”, then press ▶ or ENTER.

3 Press ▲ or ▼ to select “Signal Type”. 4 Press ◀ or ▶ to select “Air” or “Cable”.

Air - VHF/UHF channels

Cable - CABLE TV channels

Auto Ch Memory

Signal Type	Cable
Automatic Search	Start

: Select : Adjust

CABLE CHART

The chart below is typical of many cable system channel allocations.

NOTE:

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

Automatic Search

1 Select “Channel”, then press ▶ or ENTER.

2 Press ▲ or ▼ to select “Auto Ch Memory”, then press ▶ or ENTER.

3 Press ▲ or ▼ to select “Automatic Search”, then press ▶ or ENTER.

Auto Ch Memory

Signal Type	Cable
Automatic Search	Stop

Analog Channel Found : 7

Digital Channel Found : 5

Programming Now

: SelectENTER:Cancel

	The TV will begin memorizing all the channels
4 available in your area.
	• It may take from 15 minutes to 30 minutes to
	complete memorizing digital cable channels.
	Depending on the reception condition, a bar
	display may not advance for several minutes,	ENGLISH
	evening “PRIMETIME” hours, as more stations are
	please be patient.
NOTE:
•	Memorizing channels is best accomplished during
	broadcasting digital signals. Memorizing channels can
	only be accomplished while a station is broadcasting
•	a digital signal to set that channel into memory.
	If you are unsure of the digital channels available
	in your area, you may visit www.antennaweb.org to
	receive a list based on your address or zip code.
	Should you require further assistance you may call
•	our toll-free customer service line at 1-800-289-0980.
	New digital channels may be added to your area
	periodically, it is recommended to perform the
	“Automatic Search” procedure regularly.

Adding Channel

If you find a new digital channel unregistered, you can add the new channel into the channel memory.

1 Tune in the new channel.

2 Select “Channel”, then press ▶ or ENTER.

3 Press ▲ or ▼ to select “Add/Delete”, then press ▶ or ENTER.

Add/Delete

Adding Channel	>>
Add/Delete	>>
Clear All	>>
: Select	ENTER:Set

4 Press ▲ or ▼ to select “Adding Channel”, then press ▶ or ENTER. The new channel will be added into the channel memory.

Add/Delete channel

You can select the channel that you want to skip.

1

2

3

4

CH	Signal
2	Analog	Add
3	Analog	Add
3-1	Digital	Delete
3-2	Digital	Add
4	Analog	Delete
: Select	: Adjust

5 Press ◀ or ▶ to select “Add” or “Delete”, whichever function you want to perform.

6 Repeat steps 4 - 5 for other channels you want to add or delete.

19