Sony SLV-ED818ME, SLV-ED817TH Precautions, Safety, Installing, Compatible colour/TV systems

Page 2

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

The mains lead must only be changed at a qualified service shop.

Precautions

Safety

This unit operates on 110 – 240 V AC, 50/60 Hz. Check that the unit’s operating voltage is identical with your local power supply.

If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.

The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.

Unplug the unit from the mains if you do not intend to use it for an extended period of time. To disconnect the lead, pull it out by the plug, never by the lead.

Installing

Allow adequate air circulation to prevent internal heat buildup.

Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.

Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.

Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.

Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.

Do not place heavy objects on the unit.

If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about four hours before operating the unit.

Caution

Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.

Compatible colour/TV systems

This VCR is designed to record and play back using the PAL (B/G, D/K and I), MESECAM (B/G and D/K) and NTSC colour systems. Recording of video sources based on other colour systems cannot be guaranteed.

NTSC colour signals can only be recorded through the line input.

2

Introduction

Image 2
Contents Video Cassette Recorder Installing PrecautionsSafety Compatible colour/TV systemsTable of contents Getting Started UnpackingChecking your model name Inserting the batteries Setting up the remote commanderUsing the remote commander You can use this remoteConnecting the VCR Connecting the aerialAudio/video cable not supplied Additional connectionsTo a TV that has audio/video input jacks Audio cable not suppliedPress RF Channel on the VCR Tuning your TV to the VCRPress ?/1 ON/STANDBY to turn on the VCR This channel will now be referred to as the video channelIf your TV system is Select You want to play a tape, set the TV to the video channelTo obtain a clear picture from the VCR SLV-ED915PS/TH SystemTurn on your TV and set it to the video channel Selecting a LanguageBefore you start… Press M/m to select the desired languageChannels using the One Touch Tuning function Presetting channelsPresetting all receivable To check if the channels are preset correctlyTurn on the VCR and the TV Presetting all receivable channels automaticallyPresetting channels Getting Started Prog + Presetting channels manuallyPress /.to move the cursor B to Press Prog +/- to select the programme position Channel coverage System B/G System D/KPress /, to get a clearer picture, then press OK Disabling unwanted programme positionsIf the picture is not clear Selected programme positionTurn on the VCR and the TV Set the TV to the video channel Setting the clockPress , to select the month and set the month using M/m Setting the clock Press OK to start the clockBasic Operations Playing a tapeBasic Operations REW StopTo set the colour system Playing a tapeAdditional tasks To play an NTSC-recorded tapeTo use the time counter Press Prog +/- to select the programme position you want to Insert a tape with its safety tab in placeRecording TV programmes RecordTo check the remaining tape length To stop recordingPress x Stop To watch another TV programme while recordingTips Recording TV programmesTo record Ntsc colour system programmes Recording TV programmes using the Easy Timer function Setting the Easy TimerRecording TV programmes using the Easy Timer function REC SpeedSetting or changing the Easy Clock Commander Do this on the VCRTo use the VCR after setting the timer To check or change the timer settingTo cancel the timer setting To stop the VCR while recording, press x StopTips Press Menu and select Timer SET/ CHECK, then press OK Setting the timer manuallyYou can preset up to eight programmes at a time Press M/m to set each itemDaily/weekly recording Setting the timer manuallyPress ?/1 to turn off the VCR Search Operations Tape meter Searching for the current position on a tapeTo stop the Search function Blank section Last recorded Searching using the Blank Search functionTo stop searching Searching using the index function Using the Index Search buttons on the remote commanderUsing the Search Mode button and Easy Timer knob on the VCR Press xSTOP Searching using the Time Search functionEasy Timer knob Press H Play Playing/searching at various speedsTo resume normal playback To extend the duration Setting the recording duration timeTo cancel the duration Press zREC repeatedly to set to the new durationChecking Changing/ cancelling timer settings Programme Will be cut off Checking/changing/cancelling timer settingsWhen the timer settings overlap To select bilingual sound while recording For SLV-ED915PS/TH only Zweiton German stereo systemNicam system Press Audio Monitor to select the sound you wantRecording stereo and bilingual programmes For SLV-ED818ME/SG, ED817TH and ED815PS onlySelecting the sound during playback How sound is recorded on a video tape Tracking meter Adjusting the pictureAdjusting the tracking APC recording About the Adaptive Picture Control APC functionAPC playback To deactivate the APC functionMenu choices Initial settings are indicated in bold printChanging menu options Menu option Set this option toEditing with another VCR How to connect to record on this VCRVMC-710/720HG audio/video cable not supplied Signal flow EditingEditing with another VCR Jack If the other VCR is Use a cable such asBefore you start editing When recording on this VCRBasic editing To stop editingAudio dubbing SLV-ED818ME/SG and ED616ME/MJ/ SG only To stop while editingAdditional Information TroubleshootingClock Power Playback Symptom Remedy Others TroubleshootingSymptom Remedy Head Condition Sensor Sapphire tape cleanerSymptoms caused by contaminated video heads System SpecificationsSupplied accessories Inputs and outputsRefer to the pages indicated in parentheses for details Index to parts and controlsFront panel Display window Index to parts and controlsVideo jacks Mains lead Aerial OUT connector LINE-1 in AUDIO/VIDEO jacksRear panel for SLV-ED616ME/MJ/SG and ED515PS only Remote commander Index V, W, X, Y