Sylvania SRPD442 owner manual Operating the Plasma Display, Basic Operations, Power, Input Select

Page 10

OPERATING THE PLASMA DISPLAY

BASIC OPERATIONS

POWER

VOL

POWER

MUTE

SCREEN MODE

STILL

INPUT SELECT

INPUT SELECT

DISPLAY

The following is a simple explanation of the pro- cedure for turning the power of the display ON or STANDBY, and the procedure for selecting the input signal.

The procedure described here is for the remote control, however the POWER, INPUT SELECT, and VOLUME buttons on the plasma display can also be used in the same way.

1 Press the POWER button.

Confirm that the STANDBY indicator is lit before pressing the POWER button.

The power turns ON, and the ON indicator on the main unit lights up. The STANDBY indica- tor on the main unit disappears.

NOTE:

•It takes approximately 8 seconds for the screen to display after turning the power ON, but this is not a malfunction.

2 Select the input signal by pressing the INPUT SELECT button.

Each time you switch the input, the name of the selected input terminal is displayed on the screen for approximately 4 seconds.

NOTE:

•"No signal" is displayed on the screen if there is no input from the selected terminal and there is no message currently displayed on the screen for volume adjustment or the setup menu, etc.

•If there is no video signal, and there has been no operation from the remote control or the buttons on the main unit for more than 15 minutes, the auto shut-off function activates, switching the plasma display to standby mode.

3 Adjust the volume and screen size according to your requirements.

Perform adjustments to the volume (VOL K / L button), screen aspect ratio (SCREEN MODE button), and picture settings (MENU button)

NOTE:

•When you adjust the volume with the VOL K / L button, a message such as the following is dis- played on the screen. This message disappears approximately 4 seconds after performing adjust- ments.

•If you turn the audio mute on, a message slowly flashes on the screen. At this time, if you press another button, this flashing stops.

•To turn the audio mute off, either press the MUTE button again, or press the VOL K / L button.

•If you press either the PREVIOUS, K, L, B, or { button in a mode apart from the image adjustment mode. A message such as the following is dis- played.

4 Press the POWER button to turn the power

STANDBY.

The ON indicator on the main unit disappears, and the STANDBY indicator lights up.

NOTE:

•You cannot turn the power ON for approximately 3 seconds after the power enters the standby mode. Do not turn the power STANDBY and then ON again in a short time interval.

•Even if the power is turned STANDBY, the main unit is in the standby mode. In order to shut the main power of the display OFF, it is necessary to remove the AC cord from the power outlet.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Plasma Display Important Safety Instructions Important Safety Instructions RADIO-TV InterferenceRegarding This Manual When moving the plasma displayOptional Accessories # CautionContents Supplied Accessories Control Batteries / Remote Control Range Inserting the Remote Control BatteriesRemote Control Range SuppliedMain Unit Component NamesFront Rear Names Remote ControlVOL Kup / Ldown button Increases or decreases the volume Input Select button Selects input termiOperating the Plasma Display PowerPress the Power button to turn the power Basic OperationsSelecting the Input Signal Selecting the Input SignalDisplaying the Current Input Signal DisplayScreen Mode Changing the Aspect Ratio Screen ModeMode Picture Explanation Sleep Press the Still button again to turn the Still mode offStill StillLayout of the Setup Menu Navigating the SET UP MenuVarious functions in the setup menu are outlined below Menu Entering the Main MenuPicture Select Menu PreviousSelect screen with the K / L buttons Automatically Adjusting the Picture SettingsSelect Picture mode on the Picture Press the Previous button to return toSelect Window setting on the Main Menu Window SettingInitializing the Adjustments If there is no input from a video signal, WindowSwitching the Display Language Setting the Screen Saver Setting the Screen Saver and the Background ColorSetting the Background Color External Input Terminals VideoVideo Signal Connection Better Signal Transfer Connecting Devices to the AV Input TerminalsVideo Signal Connection Basic Signal Transfer External Input TerminalsConnecting Devices to the Component Input Terminals 480i interlaced signals can be connected to ComponentTerminals Connecting Plasma Display to Audio SystemAudio Signal Connection External InputConnecting the Power Cable Attaching a Wall Mount Bracket Sold Separately Attach the plasma display to the wallCleaning the Plasma Display MaintenancePreventing Image Burn on the plasma display Troubleshooting Guide Maintenance / Warning / Troubleshooting GuideAbout Pixel Defects Troubleshooting GuideAbout Interference to Infrared Devices Check These Items and TRY These CorrectionsSpecifications SpecificationsInstalación DE LAS Pilas EN EL Control Remoto Referencia Rápida EN EspañolTraslado de la unidad principal Unidad Principal Nombres DE LOS ComponentesControl Remoto MY-HOME R One Year Full WarrantyYour Home Our Home
Top Page Image Contents