Sylvania SRPD442 owner manual Selecting the Input Signal, Displaying the Current Input Signal

Page 11

SELECTING THE INPUT SIGNAL

POWER

VOL

MUTE

SCREEN MODE

STILL

INPUT SELECT

INPUT SELECT

DISPLAY

DISPLAY

The procedure for selecting the input signal described here is for use with the remote control. However, the INPUT SELECT button on the plas- ma display can also be used in the same way.

Displaying the Current Input Signal

1 Press the DISPLAY button.

The name of the current input terminal is dis- played on the screen.

2 To clear the name of the current input terminal, press the DISPLAY button again, or wait for approximately 4 seconds.

NOTE:

•To redisplay the name of the input terminal, press the DISPLAY button again.

Selecting the Input Signal

1 Press the INPUT SELECT button to select the input signal.

Each time you switch the input signal, the name of the selected input terminal is dis- played on the display for approximately 4 sec- onds.

The INPUT SELECT button cycles through the input terminals in the following pattern:

Video 1

Video 2

Component 1

 

(S-Video 1)

(S-Video 2)

 

 

DISPLAY

 

Component 2

 

 

 

 

NOTE:

 

 

 

• When switching the input signal, audio mute turns

PLASMA

ON temporarily.

 

 

 

 

 

• S-VIDEO1 takes preference over the VIDEO 1

 

jack, as does S-VIDEO 2 over the VIDEO 2 jack.

 

Therefore, if there is input to the VIDEO and S-

 

VIDEO terminals at the same time, the S-VIDEO

THE

signal is displayed on the screen. If the S-VIDEO

 

cable is not connected to the plasma display, the

OPERATING

VIDEO signal will be displayed on the screen.

 

• 480i (interlaced) signals can be connected to the

 

COMPONENT 1 and 2 terminals. Any of the fol-

 

lowing display formats: 480i, 480p (progressive),

 

1080i, and 720p (progressive) signals can be con-

 

nected to the COMPONENT 2 terminal. If one of

 

these video signals is detected, the format of the

 

input signal is displayed after the name of the cur-

 

rent input terminal, as in the following manner.

 

• A "No signal" message appears if there is no video

 

signal, and there is no message currently dis-

 

played on the screen for volume adjustment or the

 

setup menu, etc. If there continues to be no video

 

signal for more than 10 seconds, "No signal" slow-

 

ly moves around the screen.

 

 

• If there is no video signal, and there has been no

 

operation from the remote control or the buttons

 

on the main unit for more than 15 minutes, the

 

auto shut-off function activates, and the display

 

switches to standby mode.

 

 

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Plasma Display Important Safety Instructions RADIO-TV Interference Important Safety Instructions# Caution When moving the plasma displayOptional Accessories Regarding This ManualContents Supplied Accessories Supplied Inserting the Remote Control BatteriesRemote Control Range Control Batteries / Remote Control RangeFront Rear Component NamesMain Unit Input Select button Selects input termi Remote ControlVOL Kup / Ldown button Increases or decreases the volume NamesBasic Operations PowerPress the Power button to turn the power Operating the Plasma DisplayDisplay Selecting the Input SignalDisplaying the Current Input Signal Selecting the Input SignalMode Picture Explanation Changing the Aspect Ratio Screen ModeScreen Mode Still Press the Still button again to turn the Still mode offStill SleepVarious functions in the setup menu are outlined below Navigating the SET UP MenuLayout of the Setup Menu Menu Previous Entering the Main MenuPicture Select MenuPress the Previous button to return to Automatically Adjusting the Picture SettingsSelect Picture mode on the Picture Select screen with the K / L buttonsIf there is no input from a video signal, Window Window SettingInitializing the Adjustments Select Window setting on the Main MenuSwitching the Display Language Setting the Background Color Setting the Screen Saver and the Background ColorSetting the Screen Saver Video External Input TerminalsExternal Input Terminals Connecting Devices to the AV Input TerminalsVideo Signal Connection Basic Signal Transfer Video Signal Connection Better Signal Transfer480i interlaced signals can be connected to Component Connecting Devices to the Component Input TerminalsExternal Input Connecting Plasma Display to Audio SystemAudio Signal Connection TerminalsConnecting the Power Cable Attach the plasma display to the wall Attaching a Wall Mount Bracket Sold SeparatelyPreventing Image Burn on the plasma display MaintenanceCleaning the Plasma Display Maintenance / Warning / Troubleshooting Guide Troubleshooting GuideCheck These Items and TRY These Corrections Troubleshooting GuideAbout Interference to Infrared Devices About Pixel DefectsSpecifications SpecificationsTraslado de la unidad principal Referencia Rápida EN EspañolInstalación DE LAS Pilas EN EL Control Remoto Control Remoto Nombres DE LOS ComponentesUnidad Principal Our Home One Year Full WarrantyYour Home MY-HOME R
Top Page Image Contents