Remote Control ANTENNA/CATV Connections, 51843

REMOTE CONTROL

(CONTINUED)

ANTENNA/CATV CONNECTIONS

C-T1421

No.

BATTERY INSTALLATION

1.Open the battery compartment cover in the direction of the arrow.

2.Install two “AAA” (penlight size) batteries, paying attention to the polarity diagram in the battery compartment.

3. Replace the compartment cover.

BATTERY PRECAUTIONS

The precautions below should be followed when using batteries in this device:

1.Use only the size and type of batteries specified.

2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–end” first.

3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

5.Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)

Combination VHF/UHF Antenna

Single 75 ohm Cable

300 ohm Twin-lead Wire
Splitter	Take off the Splitter

UHF Antenna	300-75 ohm
300 ohm Twin-lead Wire	Matching Transformer
300 ohm Twin-lead Wire

VHF Antenna

Single 75 ohm Cable

300 ohm Twin-lead Wire

	Combiner
	(not supplied)
Incoming CATV	300-75 ohm
Incoming CATV	Matching Transformer

Converter/Descrambler

Splitter	A/B Switch	A B

Combination VHF/UHF Antenna (Single 75 ohm Cable or 300 ohm Twin-lead Wire)

This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box. Some cable companies offer "premium pay channels" in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.

Indoor Antenna

A single pole antenna is supplied with the unit (C-T1421 only), insert the antenna holder into the mounting hole on the back of the cabinet until it locks into place. Attach the antenna plug to the antenna jack. Adjust the length and angle of the antenna rod to receive the best possible picture.

Separate VHF/UHF Antennas

Connect the 75 ohm Cable from the VHF antenna and the UHF antenna Twin-lead to a combiner (not supplied). Attach the Combiner to the Antenna Jack.

NOTE:If your VHF antenna has a Twin-lead Wire, use the 300- 75 ohm Matching Transformer, then connect the Transformer to the Combiner.

For Subscribers to Basic Cable TV Service

For basic cable service not requiring a Converter/Descrambler box, connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack on the back of the television.

For Subscribers to Scrambled Cable TV Service

51843

EFFECTIVE DISTANCE OF THE REMOTE CONTROL TRANSMITTER

15 FEET

30˚

NOTES: • When there is an obstacle between the TV and the transmitter, the transmitter may not operate.

•When direct sunlight, an incandescent lamp, ﬂuorescent lamp or any other strong light shines on the Remote sensor of the TV, the remote operation may be unstable.

Connect the 75 ohm cable from a combination VHF/UHF antenna to the Antenna Jack. If your combination antenna has a 300 ohm Twin-lead Wire, use the 300-75 ohm Matching Transformer.

Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm Twin-leads)

Connect the UHF Twin-lead Wire to a Combiner (not supplied). Connect the VHF Twin-lead to the 300-75 ohm Matching Transformer. Attach the Transformer to the Combiner. Attach the Combiner to the Antenna Jack.

If you subscribe to a cable service which requires the use of a Converter/Descrambler box, connect the incoming cable to the Converter/Descrambler box and connect the output of the box to the Antenna Jack on the back of the television. Follow the connections shown left. Set the television to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/Descrambler box to select channels.

For Subscribers to Unscrambled Basic Cable with Scrambled Premium Channels

If you subscribe to a cable service in which basic cable channels are unscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a two-set signal splitter (sometimes called a "two-set coupler") and an A/B Switch box from the cable installer or an electronics supply store. Follow the connections shown left. With the switch in the "B" position, you can directly tune any nonscrambled channels on your TV. With the switch in the "A" position, tune your TV to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the box to tune scrambled channels.