JVC DT-V2000SU manual Function Selection Setting, Function Select item

FUNCTION SELECTION (SETTING)

You can select (set) the display’s functions.

1 Press the MENU button.	＜ＭＡＩＮ ＭＥＮＵ＞�
MENU	�

ＳＩＺＥ／ＰＯＳＩＴＩＯＮ ＡＤＪ．�

The <MAIN MENU> screen appears. ＤＩＳＴＯＲＴＩＯＮ ＡＤＪ．�

ＰＩＣＴＵＲＥ ＡＤＪ．�

ＦＵＮＣＴＩＯＮ ＳＥＬＥＣＴ� ＳＴＡＴＵＳ�

ＤＥＧＡＵＳＳ�

ＥＸＩＴ： ＭＥＮＵ�ＥＮＴＥＲ：�+ ＳＥＬＥＣＴ：�

<MAIN MENU> screen

2 Press the SELECT					＜ＭＡＩＮ ＭＥＮＵ＞�
button to select the					�
				SELECT	ＤＩＳＴＯＲＴＩＯＮ ＡＤＪ．�
					ＳＩＺＥ／ＰＯＳＩＴＩＯＮ ＡＤＪ．�
[FUNCTION SELECT] item.					ＰＩＣＴＵＲＥ ＡＤＪ．�
					ＳＴＡＴＵＳ�
					ＦＵＮＣＴＩＯＮ ＳＥＬＥＣＴ�
The selection mark ( 4) moves to					ＤＥＧＡＵＳＳ�
the [FUNCTION SELECT] item.					ＥＸＩＴ： ＭＥＮＵ�ＥＮＴＥＲ：�+	ＳＥＬＥＣＴ：�
					<MAIN MENU> screen
3 Press the	VOLUME/				＜ＦＵＮＣＴＩＯＮ ＳＥＬＥＣＴ＞�
ENTER		button.			�	：ＯＶＥＲ�
					ＳＣＡＮ ＳＩＺＥ
					ＲＧＢ／ＣＯＭＰＯ．	：ＲＧＢ�
					ＡＳＰＥＣＴ	：４－３�
The <FUNCTION SELECT> screen					ＣＯＬＯＲ ＳＷ	：ＯN�
					ｒｅｓｅｔ�	：ＨＩＧＨ＊�
					ＣＯＬＯＲ ＴＥＭＰ．
appears.
					ＥＸＩＴ： ＭＥＮＵ�ＡＤＪＵＳＴ：�－ ＋� ＳＥＬＥＣＴ：�
					<FUNCTION SELECT> screen
4 Press the SELECT					＜ＦＵＮＣＴＩＯＮ ＳＥＬＥＣＴ＞�
button to select			SELECT		�
					ＳＣＡＮ ＳＩＺＥ	：ＯＶＥＲ�
					ＲＧＢ／ＣＯＭＰＯ．	：ＲＧＢ�
the desired adjustment					ＡＳＰＥＣＴ	：４－３�
					ＣＯＬＯＲ ＴＥＭＰ．	：ＨＩＧＨ＊�
					ＣＯＬＯＲ ＳＷ	：ＯN�
item.					ｒｅｓｅｔ�
The selection mark ( 4) moves to					ＥＸＩＴ： ＭＥＮＵ�ＡＤＪＵＳＴ：�－ ＋� ＳＥＬＥＣＴ：�
the adjustment item.					<FUNCTION SELECT> screen

5Perform adjustment with the VOLUME/

ENTER/buttons.

* Items not displayed because of the selected input mode (INPUT SELECT) cannot be adjusted.

Items			Contents
RGB/COMPO.	Sets the input signal of the INPUT A terminal to receive
	RGB or component (COMPO.) signals.
	(RGB p[COMPO.)
	RGB	: RGB signal is selected.
	COMPO. : component signal is selected.
SCAN SIZE	Sets the scan size when component (COMPO.) signals
	are input to the INPUT A terminal.
	(OVER p[UNDER)
	p	p
	OVER : standard scan size (95% overscan) is
		selected.
	UNDER : underscan size is selected.
ASPECT	Sets the aspect ratio for INPUT B signals and INPUT A
	component (480i, 480p) signals.
	(4-3 p[ 16-9)
	4-3 : sets the aspect ratio to 4:3. (Standard for INPUT B
		signals.)
	16-9 : sets the aspect ratio to 16:9. (Standard for INPUT A
		component (480i, 480p) signals.)
COLOR SW	Sets the color switch of the INPUT B signal input and the
	INPUT A component (COMPO.) signal input.
	(ONp[ OFF)
	ON : usually keep COLOR SW set to ON (the picture is
		colored).
	OFF : the colored picture becomes black and white.
COLOR TEMP.	Sets the color temperature to HIGH or LOW
	(HIGH p[ LOW).
	HIGH : sets the color temperature to HIGH.
	LOW : sets the color temperature to LOW.

•RGB/COMPO. : sets the input signal of the INPUT A terminal

• SCAN SIZE	: sets the scan size
• ASPECT	: sets the aspect ratio
• COLOR SW	: sets the color switch

•COLOR TEMP. : sets the color temperature

RESETTING ITEMS TO THEIR FACTORY-SET (INITIAL) VALUES

You can reset each item (RGB/COMPO., SCAN SIZE, ASPECT COLOR SW and COLOR TEMP.) in the <FUNCTION SELECT> menu to their factory-set (initial) values.

1Select the [ reset] item in procedure 4.

2Press the VOLUME/ENTER

button.

The <reset> screen appears.			＜ｒｅｓｅｔ＞�
		�
3Perform adjustment with the		Ａｒｅ ｙｏｕ ｓｕｒｅ？�
		“ＹＥＳ“ ｔｈｅｎ ＋�		ｋｅｙ．�
VOLUME/ENTER	button or	“ＮＯ“	ｔｈｅｎ ＭＥＮＵ� ｋｅｙ．�

the MENU button.

MENU

<reset> screen

VOLUME/ENTER button… Values are reset. MENU button… Reset is aborted

MENU

(values are unchanged).

* The screen from procedure 4 reappears.

6After adjustment is complete, press the

MENUbutton twice to exit the menu screen.MENU

Notes:

●The menu screen automatically disappears when no operation is performed after about 30 seconds.

●When a prompt appears in the menu screen, it does not disappear until the operation requested is performed.

●Before setting functions, make sure that signals are being input to the monitor.

●Items that cannot be set or adjusted because of the selected input mode (INPUT SELECT) are not displayed.

●When setting the [RGB/COMPO.] item, procedure 6 is not needed. After being set, the picture temporarily disappears, then the function selection is complete.

●The [SCAN SIZE] item can be set only when INPUT B (NTSC composite or Y/C) signals or INPUT A component signals are input.

●The [ASPECT] item can be set only when INPUT B signals or INPUT A component signals (480i, 480p) are input. With INPUT B signals, 4:3 (4-3) is the standard. With INPUT A (COMPO.) signals, 16:9 (16-9) is the standard.

●The [COLOR SW] item can be set only when INPUT B signals or INPUT A component signals are input.

●When the “ * ” mark appears after the [COLOR TEMP.] setting is changed (HIGH or LOW), it means that the [WHITE BALANCE] item in the <SET-UP MENU> screen has been adjusted. [WHITE BALANCE] is different for [HIGH] and [LOW].

13