JVC AV32P10EK, AV32L5EK, AV32P10EI, AV32L5EI Adjusting the volume balance with the Test Mode

Page 25

DIGITAL SURROUND (Only AV32P10EK and AV32P10EI)

3Press the OK button to complete the setting

The menu disappears.

•When a speaker system is not connected to the TV, set TV SPEAKER to L/C/R and SUBWOOFER to OFF. Otherwise the sound will not be emitted correctly.

•When you do not want to hear sound from the TV speakers, set TV SPEAKER to OFF.

•The CENTRE (centre sound) DELAY TIME cannot be adjusted when the TV SPEAKER is set to L/C/R.

•If you set TV SPEAKER to CENTRE or OFF, the sound from the subwoofer can be heard only when listening to the Dolby Digital sound with the Low Frequency effect (LFE). If you want to hear sound from the subwoofer every time, set TV SPEAKER to L/C/R.

Adjusting the volume balance with the TEST MODE

Use the test signal to adjust the volume level of each speaker so that they are all the same.

Preparation:

•The TV volume cannot be adjusted after the menu is displayed. Increase the TV volume level to about 10 before displaying the menu.

1Display the sub-menu of the DOLBY DIGITAL function

2Press the 6buttons to choose TEST MODE. Then press the 5buttons to choose ON

Test signals are output from each of the speakers in turn.

When using the front speaker system and/or subwoofer system with the TV:

Turn on the power of each amplifier, slowly increase the amplifiers’ volumes until the sound emitted from each speaker connected to the system is about the same as that of the sound emitted from the TV speakers. Note that increasing the amplifier volume too high may damage the speakers.

Stopping the test signal:

Press the 6 buttons to choose TEST MODE and press the 5buttons to choose OFF.

3Press the 6buttons to adjust the sound volume of each of the speakers.

Adjust the sound volumes so that you can listen to the sounds at the same volume when you are sitting where you would normally sit to watch the TV.

LEFT/RIGHT:

The left or right of the front speakers

CENTRE:

The centre speaker

LS/RS:

The left or right of the surround speakers

If REAR SPEAKER is set to OFF, LS and RS are not displayed.

4Press the abutton to complete the settings

The menu disappears.

•When using the front speaker system or subwoofer system with the TV, it is recommend that this TEST MODE is used to adjust the speaker volume levels each time the system is used.

25

Image 25

Contents AV32L5EK* UK model AV32L5EI* Ireland model SpecificationsIf in doubt consult a competent electrician Safety precautionsGuidelines for safe operation Connecting the aerial and video cassette recorder VCR Setting up your TVConnecting the power cord to the mains outlet Putting batteries into the remote controlPress the main power button on the TV Initial settingsFor UK model AV32P10EK/AV32L5EK To cancel the Auto Program functionFor Ireland model AV32P10EI/AV32L5EI If you do not have a T-V Link compatible VCR connectedLink functions TV auto power on/VCR Image viewPre-set download Direct RecTurn the main power on Using your TV-the basicsTurn the TV on from standby mode Choose a TV channelWatching images from External equipment Changing the volumeAV32P10EK and AV32P10EI Using the buttons on the TVBehind the Cover AV32L5EK and AV32L5EI Side of the TVMuting button Remote control buttons and functionsNumber buttons Zoom buttonChoose the Zoom mode Adjusting the visible area of the picture3D Button Only AV32P10EK AV32P10EI Zoom SubtitleInformation button VCR P DVD switchColour buttons OK button@# PIP control buttons ~ Freeze buttonPress the Freeze button Press the PIP buttonUsing the List Mode $ Teletext control buttons and VCR P DVD switchBasic operation Press and hold down the PbuttonHold CancelSub-page RevealPress the abutton to display Menu main menu Using the TV’s menusPicture adjustment Picture settingECO Mode TintDigital VNR Picture featuresDigiPure Pro VNRAuto Aspect Colour SystemPicture Tilt PIP PositionSound adjustment Sound settingStereo BBEHeadphone Subwoofer Only AV32P10EK and AV32P10EIPress the 6buttons to choose SubwooferDigital Surround Only AV32P10EK and AV32P10EI To cancel a surround functionDolby Digital 3D-PHONICDolby Digital setting 3D-PHONIC settingPress the OK button to complete the setting Other surround functionsStopping the test signal Adjusting the volume balance with the Test ModeTo cancel the DIGITAL-IN setting To cancel the S-IN S-VIDEO input settingS-VIDEO input DIGITAL-IN Only AV32P10EK and AV32P10EIDubbing ID ListTo erase a name assigned to the EXT terminal Blue Back Sleep TimerChild Lock To set the Child Lock functionTo view a locked TV channel Decoder EXT-2Press the blue button and set the Child Lock function Press the number buttons to enter the ID NumberAuto Program LanguageProgram EDIT/MANUAL To cancel the Move functionPress the 3 button to start the Move function Press the 6 buttons to choose a new programme number PRPress the 6 buttons to choose the channel name ID Press the red button to start the ID functionPress the abutton to give a channel name ID to a TV channel For Ireland model AV32P10EI/AV32L5EICH/CC Number To cancel the Manual functionPress the yellow button to delete the TV channel Press the green or red button to search for TV channelTo stop the demonstration When the Demo function is set to onUsing the Decoder EXT-2 function Using the ACI functionOther menus Downloading data to a VCRTo cancel the Decoder EXT-2 function Before connecting anything Connecting external equipmentFurther preparation Behind the CoverVideo or sound signal output from the EXT-2 terminal Connecting headphonesListening to Dolby Digital audio Only AV32P10EK AV32P10EI Link compatible VCRBefore connecting anything Using additional audio EquipmentConnect the audio equipment to the TV Positioning of speakersSpeaker function Front panel TV buttons and partsRear Panel AV32L5EK and AV32L5EI AV32P10EK and AV32P10EITroubleshooting Specifications