FUNAI CR202EM9 owner manual 5Troubleshooting Guide

Page 22

TROUBLESHOOTING

5Troubleshooting Guide

If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart once before calling for service.

Symptom

Remedy

No power	• Be sure the power cord is plugged in.
	• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
	reset itself.
No picture or sound	• Check if the power is on.
	• Check the outlet connection.
	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
	• Turn off the power and wait for about 1 minute, then turn it on again.
No color	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
	• Adjust “COLOR” in “PICTURE” menu.
Sound OK, picture poor	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• Adjust “CONTRAST” and “BRIGHT” in “PICTURE” menu.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
Weak picture	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Adjust “CONTRAST” and “BRIGHT” in “PICTURE” menu.
	• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture blurred	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
Ghosts in picture	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Bars on TV screen	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on TV	• Move the unit away from nearby electric appliances. Turn off the power and wait
screen	30 minutes before turning it back on.
	• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some	• Check the antenna or cable connection to the main unit.
channels	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor	• View other TV channels. The problem might be limited to the broadcasting station.

No reception of digital signals	• Make sure auto channel scan has been completed. (Refer to “Auto Channel Scan”
	on page 11.)
	Auto channel scan must be completed when you set up the unit for the first time
	or move it to a location where previously unavailable channels are broadcast.
	• The selected channel may not be broadcasting.
	• When auto channel scan is interrupted and not completed, some channels will not
	be received. Make sure to complete. (Refer to “Auto Channel Scan” on page 11.)

22

EN

Image 22

Contents To Receive DIGITAL/ANALOG SIGNAL, YOU Must Connect Antenna CR202EM9Introduction Important note is located on the rear of the cabinetPrecautions RADIO-TV InterferenceLocation 5Supplied Accessories5Symbols Used in this Manual To Avoid the Hazards of Electrical Shock and FireContents FeaturesDTV/TV/CATV 5Remote Control Function 5Installing the Batteries5Control Panel 5Rear PanelAntenna Cable Connection Connection5Basic Connection Connection to Cable Box or Satellite BoxRCA video cable 5External Device ConnectionVideo or Video Cable Connection Rear Video Cable Connection Front5Initial Setup Initial Setting5Main Menu Scanning and memorizing the channels automatically start 5Auto Channel Scan5Language Selection EnglishWatching TV 5Volume AdjustmentUse VOL X / Y to adjust the audio volume 5Channel SelectionDigital Mode 5Switching Each ModeAnalog Mode 5Screen Information5TV Screen Display Mode 5Sleep Timer5Channel Add/Delete Optional SettingTo add or delete another channels, repeat steps 4 to Tint Sharpness 5Picture AdjustmentOFF CAPTION1 Bright CAPTION2 Contrast CAPTION35DTV Closed Caption Press Menu to exit5DTVCC Style Chip DpageTV Rating To Set the Sub RatingsMpaa Rating Troubleshooting 5Troubleshooting GuideWith an AM radio MaintenanceWith a digital camera including built-in cell phone cameras Information Memo Limited Warranty Manual del Usuario Importante para su Seguridad IntroducciónCuidado PrecaucionesInterferencia DE RADIO-TELEVISIÓN Ubicación 5Accesorios Suministrados5Símbolos Utilizados en este Manual Para Evitar LOS Riesgos DE Descarga Eléctrica E IncendioCaracterísticas Contenido5Función de Mando a Distancia 5Instalación de las Pilas5Panel de Control 5Panel TraseroConexión de Cable de Antena Conexión5Conexión Básica Conexión a Caja de Cable o Caja de SatéliteCable S-video 5Conexión de Dispositivo ExternoConexión de Cable de S-video o de Vídeo Trasera Conexión de Cable de Vídeo DelanteraAjuste Inicial 5Configuración Inicial5Menú Principal 5Selección de Idioma Español5Selección de Canal 5Ajuste de VolumenPara VER LA Televisión Para utilizar los botones numéricos5Para Cambiar entre Cada Modo 5Información de PantallaAncho Buzón 5Modo de Visualización de Pantalla del Televisor5Temporizador de Apagado ZoomUtilice VOL X / Y para seleccionar Agregar o Borrar Ajuste Opcional5Agregar/Borrar Canales Para agregar o borrar otros canales, repita los pasos5Ajuste de Imagen SubtítulosLuego presione VOL Utilice CH Para seleccionar DTVCC, y luego5Estilo Dtvcc Cuando no haya configurado su contraseña, introduzca ChipClase de TV Para Ajustar las SubcategoríasClase de Mpaa Vuelva a introducir la contraseña en el espacioSolución DE Problemas 5Guía de Solución de ProblemasSintonice la emisora de radio AM en una frecuencia MantenimientoDe no emisión. Apunte con el mando a distancia Información EMO Funai Service Corporation Servicio de atención al cliente Garantía Limitada