22
Troubleshooting
PROBLEMS | CHECK |
There is no power | • See if the power cord became unplugged. |
| • Check for a blown fuse or circuit breaker or a power outage. |
|
|
There is no picture | • The antenna could be disconnected. |
or sound | • The input mode could be set improperly. See page 40. |
| • The tuner (Auto Tuner Setup) could be set improperly. See page 20. |
| • The TV station may be having difficulties. Check to see if other stations are working. |
|
|
Remote control is not | • Check to see that the batteries are still working and properly installed. |
operating properly or | • Make sure the remote has a clear sight path to the TV. |
at all | • Check that the TV/CATV switch is in the proper position. |
|
|
You cannot select a | • You may be too far from the TV. You must be within 23 feet (7 meters). |
certain channel | • Make sure the channels have been programmed. See "Channel Summary", page 21. |
| • Check to see if the channel is locked. See "Channel Summary - Lock" page 21. |
|
|
The power turns off | • Make sure the set did not become unplugged. |
by itself | • Perhaps the On/Off Timer is set. See page 36. |
| • Check to see if the Sleep Timer was set. See page 39. |
|
|
The clock is wrong | • The power was interrupted and the clock was not reset. See page 34. |
|
|
The On Timer is | • There is a problem with the TV. Unplug the set and call for service. |
blinking |
|
|
|
The color quality | • Tint and Color may be improperly adjusted. See page 30. |
is poor | • The Video Status mode may be turned to the wrong setting. See page 31. |
|
|
There are lines | • There could be interference from another electrical appliance, such as a computer, |
across the picture | another TV or VCR. Move any such appliances further away from the TV. |
|
|
The picture is spotted | • There could be interference from a |
| operating nearby. Move the antenna away from the appliance or change to a coaxial |
| cable connection which is less prone to interference. |
|
|
There are double | • A building or passing airplane can reflect the original signal and produce a second, |
pictures (ghosts) | slightly delayed one. Adjust your antenna position. |
|
|
Picture is snowy | • Your antenna may be damaged, disconnected or turned. Check the antenna |
(image noise) | connection. If the antenna is damaged, replace it. |
|
|
Screen is 80% black | • The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 37. |
|
|
Stereo or bilingual | • Make sure the MTS settings are correct. See "MTS" on page 33. |
programs can't be |
|
heard |
|
|
|
There is no sound | • The TV Speaker option may be turned off. See page 33. |
from the TV's speakers |
|
|
|
Static electricity | • It is normal to feel static electricity if you brush or touch the screen. |
|
|
You hear occasional | • It is normal for the TV to make crackling sounds when first turned on or off. Unless |
crackling sounds | the sound or picture become abnormal, this is fine. |
|
|
The picture is | • Make sure the BNC connector box is properly connrcted to the TV. |
excessively bright | • The television Video input jack(RCA) is not terminated. |
|
|
Search Codes
Cable/Satellite Search Codes Function:
1)Slide the
2)Press the TV POWER and RETURN+ buttons. Hold for at least three seconds and release.
3)Press TV POWER, see if the CATV or Satellite box responds.
4)If there was a response, press RETURN+. The operating codes are now set. If there was no response, repeat Step 3. If you repeat Step 3 a total of 52 times without a response, use the remote control which came with the equipment.
5)Press RETURN+ to exit.
VCR Search Codes Function:
1)Slide the first
2)Press the VCR POWER and RETURN+ buttons. Hold for at least three seconds and release.
3)Press VCR POWER, see if the VCR responds.
4)If there was a response, press RETURN+. The operating codes are now set. If there was no response, repeat Step 3. If you repeat Step 3 a total of 80 times without a response, use the manufacturers remote control which came with the VCR.
5)Press RETURN+ to exit.
DVD Player Search Codes Function:
1)Slide the first
2)Press the DVD POWER and RETURN+ buttons. Hold for at least three seconds and release.
3)Press DVD POWER, see if the DVD player responds.
4)If there was a response, press RETURN+. The operating codes are now set. If there was no response, repeat Step 3. If you repeat Step 3 a total of 30 times without a response, use the manufacturers remote control which came with the DVD player.
5)Press RETURN+ to exit.
|
42 |
|
|
| 43 |
|
|