8
Connections
Connecting to a Camcorder
You may connect a camcorder to your television by using the front Input Jacks (Input 2). You may also connect a game console or other equipment using these jacks. Camcorders may also be connected to the television’s rear input jacks.
INPUT 2
VIDEO L MONO AUDIO R
Illustration of
1)Connect the yellow video cable out from the Camcorder’s Video Output, in to the TV’s Video Input jack.
2)Connect the white audio cable out from the Camcorder’s Left Audio Output, in to the TV’s Left Audio Input Jack.
3)Connect the red audio cable out from the Camcorder’s Right Audio Output, in to the TV’s Right Audio Input Jack.
•If your Camcorder is a mono sound model it will have only one audio jack. Connect it to the TV’s Left Audio Jack.
Headphone Connection (available on 20 inch models)
You can connect a pair of headphones or earphone to the television using the headphone jack on the front panel.
1) Plug a headphone/earphone jack into the headphone jack on the television’s front panel.
TV CATV | VCR | DVD |
| POWER |
|
|
|
| |
|
|
|
| INPUT |
VIDEO STATUS | 1 | 2 | 3 | |
|
| 4 | 5 | 6 |
DISPLAY |
| 7 | 8 | 9 |
SLEEP TIMER | 100+ | 0 RETURN+ | ||
HYPER SURROUND |
|
|
| |
|
|
|
| |
MUTING |
| + |
| V CHIP |
|
|
|
| |
|
| CH |
|
|
VOL |
| VOL | ||
|
|
| + |
|
|
| CH |
|
|
MENU |
|
|
| EXIT |
VCR CHANNEL | VCR/DVD |
| ||
PREV NEXT | POWER | TV/VCR | ||
REW |
| PLAY |
| FF |
REC | STOP | PAUSE | ||
OPEN/CLOSE |
| STILL/PAUSE | ||
TV
Remote Control
Remote Control Basics
•Before you can operate the remote control, you must first install the batteries (included). See “Changing the Batteries” at the bottom of this page for instructions. (For an illustration, please see page 7.)
•Press the POWER button to turn the television on or off.
•Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if you need to operate a cable box.
•Slide the VCR/DVD selector switch to VCR to control a VCR, slide to DVD to control a DVD player. Please see pages 16 to 18 for instructions on programming your remote control to operate a Cable box, VCR or DVD player.
•Press the CH+ and CH- buttons to scan through the channels. Tap the CH+ or CH- button to move through the channels one channel at a time.
•To move rapidly through the channels using JVC’s Hyperscan feature, press and hold CH+ or
•Press VOL+ or VOL - to raise or lower the volume. An indicator bar will appear onscreen to show you the television volume level.
•The CH+/- and VOL+/- buttons are also used to navigate JVC’s onscreen menu system.
•You can directly access specific channels using the
•For more information on remote control button features, see pages 38 to 41. For information on using the onscreen menus, see page 19.
Notes: Remote control model
|
Changing the Batteries
Push down on the remote’s back cover and slide towards the bottom to remove it.
Insert two AA batteries (supplied), carefully noting the "+" and
When batteries are installed, slide the cover back into place (until it clicks into position).
•If the remote control acts erratically, replace the batteries. Typical battery life is six months to one year. We recommend using alkaline batteries for longer battery life.
When you change the batteries, try to complete the task within three minutes. If you take longer than three minutes, the remote control codes for your VCR, DVD, and/or Cable Box may have to be reset (page
14 |
|
|
| 15 |
|
|
| ||
|