BenQ MX819ST, MX820ST, MX818ST user manual Replacing the remote control batteries

Page 13

Replacing the remote control batteries

1.To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slide it up in the direction of the arrow as illustrated. The cover will slide off.

2.Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive

(+) goes to positive and negative (-) goes to negative.

3.Refit the cover by aligning it with the base and sliding it back down into position. Stop when it clicks into place.

•Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

•Replace only with the same or equivalent type recommended by the battery manufacturer.

•Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region.

•Never throw the batteries into a fire. There may be danger of an explosion.

•If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.

Introduction 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents MX818ST/MX819ST/MW820ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsON/ OFF Remote control+/PAGE Network No function AutoOperating the Laser pointer Remote control effective rangeReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsMW820ST Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signalChanging Color Space Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options Wall ColorBasic Advanced Description of each menu Temperature Picture ModeColor Temperature Fine Tuning 3D ColorInstallation TimerSearch Color SpaceFunction Description System Setup Basic menuOperation RemoteAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkCurrent Information menu Function DescriptionSystem StatusCare of the projector MaintenanceGetting to know the lamp hour Lamp informationExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Replace the lamp cover on the projector Tighten the screws that secures the lamp Cover Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsMinimum installation requirements Wall mount installation1171 1181 Screen Minimum Ceiling Height mm = f + H + b + 60 + 274+ cSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp input Resolution Mode Frequency KHz MHzTiming Supported timing for Component-YPbPrinputNtsc Supported timing for Video and S-Video inputsLimited warranty Warranty and Copyright informationCopyright Disclaimer

MX819ST, MX820ST, MX818ST specifications

BenQ has been a prominent player in the projector market, catering to various consumer needs with innovative and high-quality solutions. Among their notable offerings are the BenQ MX818ST, MX820ST, and MX819ST projectors, specifically designed for educational institutions and small to medium-sized business environments. These models are a part of BenQ's commitment to enhancing visual learning and presentations.

The BenQ MX818ST is a short-throw projector, capable of delivering large images from a close distance. This feature proves especially beneficial in classrooms where space may be limited. With a brightness level of up to 3,100 ANSI lumens and a resolution of XGA (1024x768), it provides crisp and clear visuals, making it suitable for various lighting conditions. One of its core technologies is the DLP (Digital Light Processing) technology, which ensures vibrant colors and sharp pictures, elevating the viewing experience during lessons or presentations.

Following closely, the MX820ST builds on the strengths of the MX818ST while adding enhanced features like a higher brightness level of 3300 ANSI lumens. The MX820ST also includes BenQ’s BrightView and high contrast ratio to improve visibility and clarity, ensuring that every detail stands out regardless of ambient light. Equipped with a 1.02-1.23:1 throw ratio, it allows users to project a large screen from mere feet away. Additionally, the projector boasts multiple connectivity options, including HDMI and VGA, facilitating compatibility with various devices.

The MX819ST is another standout in this lineup, offering similar specifications to its siblings but with added features that enhance usability. This model includes improved color performance thanks to BenQ's color calibration technology, ensuring consistency in image presentation. Moreover, it offers a 10,000-hour lamp life, which reduces maintenance costs and improves efficiency by minimizing the frequency of lamp replacements. Its portability and flexible installation options make it a viable choice for both stationary and mobile presentations.

All three models are designed with user-friendly interfaces, ensuring seamless operation whether in a classroom or a boardroom. They also come equipped with advanced network management features, allowing institutions and companies to manage projector settings remotely. With eco-friendly technologies, such as energy-saving modes, these projectors help minimize environmental impact.

In summary, the BenQ MX818ST, MX820ST, and MX819ST projectors stand out in the market due to their combination of advanced technologies, user-friendly features, and robust performance. They cater to the needs of educational and business environments, providing high-quality presentations that make a lasting impact.
Top Page Image Contents