BenQ MX818ST, MX820ST, MX819ST Adjusting the projected image, Adjusting the projection angle

Page 20

Adjusting the projected image

Adjusting the projection angle

To adjust the projector:

1.Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2.Screw the rear adjuster foot to fine-tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 21 for details.

2

1

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the quick- release button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image clarity

Sharpen the image by rotating the focus ring.

20 Operation

Page 19 Page 21
Image 20
Page 19 Page 21
Contents MX818ST/MX819ST/MW820ST Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions ProjectorRemote control ON/ OFF+/PAGE Network No function AutoRemote control effective range Operating the Laser pointerReplacing the remote control batteries Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeMW820ST Connection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Changing Color Space Switching input signalDisabling the password function Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Setting a preferred color temperature 3D Color ManagementSelection Description Setting the presentation timerResetting current or all picture modes To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates Direct power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options Wall ColorBasic Advanced Description of each menu Picture Mode TemperatureColor Temperature Fine Tuning 3D ColorTimer InstallationSearch Color SpaceSystem Setup Basic menu Function DescriptionOperation RemoteSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkInformation menu Function Description CurrentSystem StatusMaintenance Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Timing of replacing the lamp Status MessageReplacing the lamp Replace the lamp cover on the projector Resetting the lamp timer Tighten the screws that secures the lamp CoverIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationWall mount installation Minimum installation requirements1171 1181 Minimum Ceiling Height mm = f + H + b + 60 + 274+ c ScreenKHz Timing chartSupported timing for PC input Resolution Mode Frequency KHz MHz Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput TimingSupported timing for Video and S-Video inputs NtscWarranty and Copyright information Limited warrantyCopyright Disclaimer

MX819ST, MX820ST, MX818ST specifications

BenQ has been a prominent player in the projector market, catering to various consumer needs with innovative and high-quality solutions. Among their notable offerings are the BenQ MX818ST, MX820ST, and MX819ST projectors, specifically designed for educational institutions and small to medium-sized business environments. These models are a part of BenQ's commitment to enhancing visual learning and presentations.

The BenQ MX818ST is a short-throw projector, capable of delivering large images from a close distance. This feature proves especially beneficial in classrooms where space may be limited. With a brightness level of up to 3,100 ANSI lumens and a resolution of XGA (1024x768), it provides crisp and clear visuals, making it suitable for various lighting conditions. One of its core technologies is the DLP (Digital Light Processing) technology, which ensures vibrant colors and sharp pictures, elevating the viewing experience during lessons or presentations.

Following closely, the MX820ST builds on the strengths of the MX818ST while adding enhanced features like a higher brightness level of 3300 ANSI lumens. The MX820ST also includes BenQ’s BrightView and high contrast ratio to improve visibility and clarity, ensuring that every detail stands out regardless of ambient light. Equipped with a 1.02-1.23:1 throw ratio, it allows users to project a large screen from mere feet away. Additionally, the projector boasts multiple connectivity options, including HDMI and VGA, facilitating compatibility with various devices.

The MX819ST is another standout in this lineup, offering similar specifications to its siblings but with added features that enhance usability. This model includes improved color performance thanks to BenQ's color calibration technology, ensuring consistency in image presentation. Moreover, it offers a 10,000-hour lamp life, which reduces maintenance costs and improves efficiency by minimizing the frequency of lamp replacements. Its portability and flexible installation options make it a viable choice for both stationary and mobile presentations.

All three models are designed with user-friendly interfaces, ensuring seamless operation whether in a classroom or a boardroom. They also come equipped with advanced network management features, allowing institutions and companies to manage projector settings remotely. With eco-friendly technologies, such as energy-saving modes, these projectors help minimize environmental impact.

In summary, the BenQ MX818ST, MX820ST, and MX819ST projectors stand out in the market due to their combination of advanced technologies, user-friendly features, and robust performance. They cater to the needs of educational and business environments, providing high-quality presentations that make a lasting impact.
Top Page Image Contents