BenQ MX818ST, MX820ST, MX819ST user manual m Feet

Page 5

Safety Instructions (Continued)

13.Do not place this projector in any of the following environments.

-Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

-Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

-Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.

-Locations near fire alarms

-Locations with an ambient temperature above 40°C / 104°F

-Locations where the altitudes are higher than 3000 m (10000 feet).

3000 m

(10000 feet)

0m

(0 feet)

14.Do not block the ventilation holes.

-Do not place this projector on a blanket, bedding or any other soft surface.

-Do not cover this projector with a cloth or any other item.

-Do not place inflammables near the projector.

If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.

15.Always place the projector on a level, horizontal surface during operation.

-Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.

16.Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

Important safety instructions

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents MX818ST/MX819ST/MW820ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsON/ OFF Remote control+/PAGE Network No function AutoOperating the Laser pointer Remote control effective rangeReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsMW820ST Connection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Changing Color Space Switching input signalDisabling the password function Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Setting a preferred color temperatureSelection Description Setting the presentation timerResetting current or all picture modes Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the teaching templates Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options Wall ColorBasic Advanced Description of each menu Temperature Picture ModeColor Temperature Fine Tuning 3D ColorInstallation TimerSearch Color SpaceFunction Description System Setup Basic menuOperation RemoteAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkCurrent Information menu Function DescriptionSystem StatusCare of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Replace the lamp cover on the projector Tighten the screws that secures the lamp Cover Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsMinimum installation requirements Wall mount installation1171 1181 Screen Minimum Ceiling Height mm = f + H + b + 60 + 274+ cKHz Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input Resolution Mode Frequency KHz MHzTiming Supported timing for Component-YPbPrinputNtsc Supported timing for Video and S-Video inputsLimited warranty Warranty and Copyright informationCopyright Disclaimer

MX819ST, MX820ST, MX818ST specifications

BenQ has been a prominent player in the projector market, catering to various consumer needs with innovative and high-quality solutions. Among their notable offerings are the BenQ MX818ST, MX820ST, and MX819ST projectors, specifically designed for educational institutions and small to medium-sized business environments. These models are a part of BenQ's commitment to enhancing visual learning and presentations.

The BenQ MX818ST is a short-throw projector, capable of delivering large images from a close distance. This feature proves especially beneficial in classrooms where space may be limited. With a brightness level of up to 3,100 ANSI lumens and a resolution of XGA (1024x768), it provides crisp and clear visuals, making it suitable for various lighting conditions. One of its core technologies is the DLP (Digital Light Processing) technology, which ensures vibrant colors and sharp pictures, elevating the viewing experience during lessons or presentations.

Following closely, the MX820ST builds on the strengths of the MX818ST while adding enhanced features like a higher brightness level of 3300 ANSI lumens. The MX820ST also includes BenQ’s BrightView and high contrast ratio to improve visibility and clarity, ensuring that every detail stands out regardless of ambient light. Equipped with a 1.02-1.23:1 throw ratio, it allows users to project a large screen from mere feet away. Additionally, the projector boasts multiple connectivity options, including HDMI and VGA, facilitating compatibility with various devices.

The MX819ST is another standout in this lineup, offering similar specifications to its siblings but with added features that enhance usability. This model includes improved color performance thanks to BenQ's color calibration technology, ensuring consistency in image presentation. Moreover, it offers a 10,000-hour lamp life, which reduces maintenance costs and improves efficiency by minimizing the frequency of lamp replacements. Its portability and flexible installation options make it a viable choice for both stationary and mobile presentations.

All three models are designed with user-friendly interfaces, ensuring seamless operation whether in a classroom or a boardroom. They also come equipped with advanced network management features, allowing institutions and companies to manage projector settings remotely. With eco-friendly technologies, such as energy-saving modes, these projectors help minimize environmental impact.

In summary, the BenQ MX818ST, MX820ST, and MX819ST projectors stand out in the market due to their combination of advanced technologies, user-friendly features, and robust performance. They cater to the needs of educational and business environments, providing high-quality presentations that make a lasting impact.
Top Page Image Contents