DirecTV D10 manual Directv Receiver Back Panel, Place Batteries in the Remote Control

Page 12

Connections & Setup

DIRECTV® Receiver Back Panel

This diagram illustrates each of the back panel jacks found on your DIRECTV Receiver. When working with cables, be sure to connect corresponding outputs and inputs (VIDEO output to VIDEO input, Right AUDIO output to Right AUDIO input, etc.).

������

 

 

�

�

�

�����

 

 

�����

����������

 

 

 

 

���� ���������

����������

 

 

 

 

������������

 

 

 

 

 

 

�������

�

�

�

 

 

 

 

 

 

 

 

�����

�����

�����

 

 

 

 

�

�

 

 

����������

�������

 

 

 

Back Panel Jacks and Switches (in alphabetical order)

AUDIO (R and L) Audio cables offer better sound quality than RF coaxial cables. You can connect a second set of audio cables to another component, such as a VCR or stereo.

CH 3-4If you're using the Basic Connection (described on pages 8-9), this switch allows you to set which channel (either 3 or 4) you'd like to use on your TV to watch DIRECTV® programming (try to use the one that's "empty" in your area).

LOW SPEED DATA This port allows you to connect your DIRECTV Receiver to future services and accessories as they become available. A shielded cable and additional hardware may be required.

OFF AIR IN Connect a standard TV antenna or cable feed to the DIRECTV Receiver using this jack. The cable or off-air signal will pass through the DIRECTV Receiver when you turn the receiver off.

OUT TO TV Connects the DIRECTV Receiver to your TV or VCR using RF coaxial cable. This jack provides the most basic connection, carrying average sound and video quality.

PHONE JACK Connects the DIRECTV Receiver to a telephone line. The DIRECTV Receiver requires a telephone line connection to periodically communicate with your program provider.

SATELLITE IN Use to connect the DIRECTV Receiver to the satellite dish antenna.

S-VIDEOProvides better picture quality than VIDEO or RF coaxial cable jacks. If your TV has an S-Video jack, use it along with the audio jacks (S-Video only carries picture information, not sound) to connect to your TV.

VIDEO Provides better picture quality than the OUT TO TV jack. Connect the second VIDEO jack to another device, such as a VCR. You must also connect the AUDIO cables when using the VIDEO connection.

Place Batteries in the Remote Control

Follow these steps whenever you need to install or change the batteries in your

DIRECTV Receiver’s remote control.

1. Remove the cover from the battery compartment.

2.Insert batteries in the battery compartment, matching the + and – end of each

battery.

3. Replace the cover.

10

Chapter 1

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Directv Receiver Users Guide Important Information Product InformationTable of Contents Things To Consider Before You Connect Components Jacks and CablesConnections & Setup Insert Your Access CardChoose Your Connection RF Coaxial Cable F-typeVCR Go to Using Your Components Excellent ConnectionMaking the Connection Directv Using Your Components Very Good ConnectionMaking the Connection Go toDirectv Receiver Using RF Coaxial cables for all connections Basic ConnectionTo view VCR recordings Place Batteries in the Remote Control Back Panel Jacks and Switches in alphabetical orderDirectv Receiver Back Panel Using Highlight and Select Complete the Guided SetupPlug in and Turn on the Receiver Highlight and select navigation has two stepsTo reset the receiver Order ProgrammingDirectv News & Info Using the Remote Control Remote Control ButtonsUsing the Remote Control Front of the Directv ReceiverUsing the Remote Control to Operate Other Components Remote Control SetupOperating Other Components Modes of OperationProgramming the Remote to Operate Your TV Controlling a Second Directv ReceiverProgram Guide Displaying the Program GuideDisplaying the Quick Menu in the Guide Features of the Directv Receiver Getting Around In the GuideChannel Banner Icons of the Channel BannerSettings Quick MenuQuick Menu in the Guide Category SortDate & Time FavoritesFind By To move to a different time in the program guideCaller ID & Messages Parental ControlsUsing the Menu System Quick Menu ItemsExiting Quick Menus and Menu Screens Retracing Your StepsUsing On-Screen Menus SettingsSetup Test Signal Strength Repeat Satellite Dish SetupReset Satellite Info SatelliteRemote AudioDisplay Scheduler Audio Options ManualTo set your preferred audio language To set up a new custom channel list Find ByFavorites To choose the current channel listPrevious Channels Caller ID & MessagesCaller ID Setting Up Caller ID Caller ID IndicatorsReceiving Calls To access the call log Turning Notification On or OffCall Log Deleting CallsEdit Settings To Edit Your Parental Control SettingsParental Controls MessagesLock Now Unlock NowRatings Temporarily Unlocking the SystemMovies TV-14TV-Y7 Content Themes To block program contentTo unblock program content OtherLock Now Channel BlocksSpending HoursTroubleshooting Problems with Caller IDScreen goes blank during Satellite Data Acquisition Wrong pictureOther Information Fine-Tuning the Signal Running the System TestFinding the TV’s Video Line Input Limited 90 DAY Warranty Directv Protection Plan FCC Customer Information FCC Declaration of ConformityIndex Tocom

D10 specifications

The DirecTV D10 is a satellite television receiver that played a significant role in the evolution of digital broadcasting. Launched in the early 2000s, the D10 was designed with user-friendly features and advanced technologies that made satellite TV accessible and enjoyable for many households.

One of the standout features of the DirecTV D10 is its ability to receive over 150 channels, including a variety of local and national broadcasts. This wide range of programming options catered to diverse viewer preferences, covering genres such as sports, news, movies, and family entertainment. With its capability to receive both standard and high-definition channels, the D10 positioned itself as a versatile option for consumers looking to enjoy a diverse array of content.

The DirecTV D10 utilized advanced digital MPEG-2 technology, which allowed for superior video and audio quality. This technology ensured that viewers experienced clear images and rich sound, enhancing the overall viewing experience. The D10 also featured a built-in electronic programming guide (EPG), making it easier for users to navigate and discover new shows. The EPG provided detailed information about programming schedules, facilitating more efficient planning for viewers.

Another notable characteristic of the D10 was its compact design, allowing it to fit seamlessly into various home entertainment setups. The receiver was equipped with multiple output options, including RCA and S-Video connections, ensuring compatibility with a wide range of television models. Its user-friendly remote control was designed for intuitive navigation, making it easy for users of all ages to operate the device.

The DirecTV D10 also offered features such as parental controls, allowing families to manage content access, as well as the capability to add additional receivers, enhancing the viewing experience across multiple rooms in a home. Although the D10 has since been succeeded by more advanced models, its legacy remains impactful in the realm of satellite television.

In summary, the DirecTV D10 served as a pivotal receiver that combined multiple features, cutting-edge technology, and user-friendly characteristics, drawing in a broad audience. It helped pave the way for the modern era of digital television, making it an important piece of broadcasting history.
Top Page Image Contents