Loewe L 32, L 37, L 42, A 42 manual Directing DVB-T antenna, Switching on/off

First installation Daily operation

Directing DVB-T antenna

Note: not with DVB-T stations in UK.

If you use a room antenna to receive one or more DVB-T stations that have picture and sound interference, then you should change the location of where the antenna is set up. To help you direct your antenna or to help you determine the most suitable location to set up the antenna, your TV set has a display for the signal quality C/N and the signal strength Level.

Consult your specialist dealer to find out which channels and frequency bands (VHF or UHF) are used to broadcast the digital TV stations in your area.

On any one channel, several digital stations are broadcast.

Select a TV channel
1.	Call the “TV menu“ via the MENU button.
2.	Use	to select “Settings“, then use		to select the menu line underneath.
3.	Select “Stations“, then use		to select the menu line underneath.

TV menu

Settings		INFO END
Stations	Parental lock Timer functions Language
Manual adjustment	...

4. Select “Manual adjustment“ and call the menu using OK (not possible for MHEG-5 device versions x27/28).

Manual adjustment
Signal source	DVB-T	DVB-C	Antenna/cable (analogue
Channel	E 05
Frequency	177.50 MHz
Name	Test
Bandwidth	7 MHz
C/N 96	Level 99

END

5.For digital stations, select “Signal source – DVB-T“.

6.Use the numerical buttons to specify the corresponding channel number. Depending on the channel selected and country, the system automatically sets the corresponding bandwidth of 7 or 8 MHz. You should only change the band- width under special circumstances - if the channel raster in your area is different from the standard.

When you receive a digital station, the system displays the signal quality C/N via a bar/numeric value and the signal strength via Level. The antenna‘s direction or position is best when the largest values possible are displayed (long bar) for the signal quality and signal strength.

7.Direct the antenna so that the largest numerical value/bar size is reached.

8.If no signal is found in the channel set, you can start the frequency search run by pressing the blue coloured key within the band selected.

9.Check the other channels one after another on which digital stations are broad- cast terrestrially in your area.

For the weakest station, direct the antenna so that the maximum numerical value/bar size is achieved.

10.After you position or direct the antenna, we recommend to search for all the stations using the “Search wizard“ (TV menu – Settings – Stations – Search wizard).

Switching on/off

Your TV is equipped with an eco-standby power supply unit. On standby, the power consumption drops to low power. If you want to save even more electricity, switch the set off with the mains switch. However, please bear in mind that EPG data (electronic programme guide) will be lost, and programmed timer recordings will not be performed by the TV.

	Switching off
	If the TV set is switched on, you can switch it to standby using
	the On/Off button O on the remote control or by using the
	indicator field on the set. The red lamp on the TV set lights up.
	If the lamp is orange, a timer recording is being made, EPG data
)	is being captured or radio operation without screen display is
	active.

	Switching on the TV set
	From standby, it is best to switch the set back on using the
	On/Off button O or by using the numeric buttons of the remote
	control (0 – 99).
	Or use the switch integrated in the indicator on the set.
)	The green indicator on the TV set lights up.
	Or switch on the TV set with OK, you can then see the station
	list and select a station.
	Switching on the radio
	With the RADIO button on the remote control
	or
	with R on the control ring of the TV set, you can switch on the
	radio.
)

If you switch off the TV set using the mains switch on the set, the indicator no longer lights up.

If the TV set is switched off via the mains switch, then you have to first switch it into standby mode via the mains switch and then switch it on with the remote control or by using the indicator window on the set.

- 14