Loewe A 42, L 37 Removing the CA module, Inserting a new CA module, Searching for new software

Page 23

Operating modes – TV

Removing the CA module

1.Switch the TV set off with the mains switch.

2.Remove the cover from the back of the set on the upper left.

3.Press the eject button at the module slot; the module is unlocked.

4.Remove the module from the set.

Inserting a new CA module

After you insert a new CA module (CI module (1 is displayed in the menu) and switch the TV set on, the following dialogue is displayed:

CA module

CI-Slot

Searching for new software

If you want to carry out a manual search for new software, proceed as follows:

1.Call the TV menu using the MENU button.

2.Confirm the “Settings“ using OK.

3.Confirm the “Miscellaneous“ using OK.

4.Select “DVB software“ and press OK.

Update digital TV software

Current version: V3.x.x

You can search for a new software version with OK.

5. If you start the search using OK, the set checks if there is a new software

Autom. station search

Your TV set has detected a new CI module. This requires a station search for all new receivable stations.

After you press the OK button, the system starts the wizard to carry out the auto- matic station search.

Check the proposed search parameters and let the set search for new stations.

Calling the CA module menu

Here you can call up information on the inserted conditional access module and the smart card. To do this, use the MENU button to call the TV menu, select the line “Settings“, “Miscellaneous“ and then the entry “CI module - xxx“ (in place of “xxx“ stands the name of the provider which is output by the smart card. The term CI module (1 displayed in the menu refers to the CA module. The content of this menu depends on the particular supplier of the CA module.

Note: This menu is only available for digital stations.

Installing new DVB software

To ensure your DVB-S receiver is always performing at the state of the art, newly developed software versions are made available from time to time; these are broadcast via satellite and can be automatically installed on your set (only possible via ASTRA1).

Software is recognised automatically

The set can determine whether a new software version is available. This occurs at night when your EPG is automatically updated. For this, your TV set has to remain in the standby mode (do not switch off using the on/off button on the set).

If a new software version has been found, the set will indicate this with an on- screen message the next time the set is switched on: You can decide whether or not you want to download the new software.

Confirm using OK, so that the new software can be loaded and installed via satellite. Continue as set out in the “Downloading software“ section

version available.

6. If there is a new version available, the set generates an on-screen message.

Update digital TV software

Current version: V3.x.x

New version: V3.1.0

Downloading software

1.If you press OK in the dialogue above, you can decide whether you want to download the new software immediately, when you switch off the set or not at all. We recommend you always carry out the update of the digital software. This is the only way to ensure your set is always up to date.

2.If you do decide to update, the software is initialised on your set and you are informed of the status with a grey bar.

Do not switch your set off during this time. This process may take up to one hour. You will be informed when the process is completed.

3.After the software is updated, you will be asked to switch your TV set off and back on again using the on/standby switch.

If the update was not carried out, you will be asked several times when you switch on the set whether you want to carry out this update.

(1 CA module has established itself as the usual market name. This cannot be taken into consideration in the menu yet.

23 -

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Operating Instructions Contents +/P Remote control TV functionsDirect recording Digital RecorderControl unit Connections to rear panel Xelos a Connections to rear panel Xelos a 32/37 and Modus L 32/37 Connections to rear panel Xelos a 42 and Modus L Welcome Set CleaningDisposal Packing and boxHeating from radiators For your safetyConnection First installationRemote control Side of the module Using the conditional access moduleSwitching on Use of the binders for Xelos A42 and Modus LStation sorting Settings can be selected by pressing one of the directionsAutomatic programming Coloured keyDirecting DVB-T antenna Switching on/offChanging stations Daily operationExample of the menu operation Basics about the Menu operationSelect Stations in the line below Call the TV menu Select SettingsInfo text indicates which settings you can make in Stations For the info systemUse P+/P- to scroll up or down through the pages This is how to select the index itemUse the OK button to call Switch off Automatic For the indexDirect control on TV set Setting the soundPicture settings Calling the index How the coloured keys work in TV modeOperating modes TV Show status displaySelect picture format Call timer overviewUnder Settings you will find the following functions Calling additional functionsDVB subtitles Searching for new software Installing new DVB softwareRemoving the CA module Inserting a new CA moduleImage+ menu Image+ demo modeImage+ Picture in picture PIP Operating modes PIPFunctions in the PIP menu Switch to split screenSetting the PIP type Switch to small PIPEPG Programme guide Using the EPGSwitch EPG on/off Operating modes EPGSelecting providers and stations Switch on TV when markedProgramming recording for recorders EPG menuAnalogue Teletext Operating modes TeletextProgramme wizard for recording via teletext Programme timer recordingsTeletext menu Display teletext menuCall radio menu Operating modes RadioRadio Radio menuStart search with the blue coloured key Login and connect equipmentConnecting video/DVD recorders Operating additional equipmentCalling AV input via the station list Timer recording with video or DVD recorderVideo playback Calling AV inputs in the AV selection Call AV selectionAudio output Audio Digital OUT Assignment of digital audio inputs and outputsAudio input Audio Digital Loewe Flat-TV Connecting other audio amplifiers or active speakers Set geometry as described for VGA/XGA connection Setting colour standardHdmi DVI connection VGA/XGA connectionLog in the component/device in the connection wizard Component video connectionSound from PC or Set Top Box Set remote control Use the remote control to operate one of the DVD playersUse the remote control to operate a recorder Return to using the remote for the TVWhat to do, if Problem Possible cause RemedyConnected Digital Link Plus does not functionReplace the Euro-AV cable Dts, MpegType Xelos a Technical dataGeneral data Type Modus LConnections Electrical dataAccessories Item no. version PIP-Tuner Digital Retrofitting optionsPlac Kaszubski Service addressesService Center Loewe
Top Page Image Contents